China 10g SFP+ Module Fiber Optical Transceiver

Features
10Gb/s serial optical interface compliant to 802.3ae 10Gbase-LR
Electrical interface compliant to SFF-8431 specifications for enhanced 8.5 and 10 Gigabit small form factor pluggable module "SFP+"
1310nm DFB transmitter, PIN photo-detector
2-wire interface for management specifications compliant with SFF 8472 digital diagnostic monitoring interface for optical transceivers
Operating case temperature:
PHY-31192-5L1, 0 °C to 70°C
Advanced firmware allow customer system encryption information to be stored in transceiver
Cost effective SFP+ solution, enables higher port densities and greater bandwidth
RoHS compliant
Applications
High-speed storage area networks
Computer cluster cross-connect
Custom high-speed data pipes
1. GENERAL DEscriptION
This 1310 nm DFB 10Gigabit SFP+ transceiver is designed to transmit and receive optical data over single mode optical fiber for link length 10km.
The SFP+ LR module electrical interface is compliant to SFI electrical specifications. The transmitter input and receiver output impedance is 100 Ohms differential. Data lines are internally AC coupled. The module provides differential termination and reduce differential to common mode conversion for quality signal termination and low EMI. SFI typically operates over 200 mm of improved FR4 material or up to about 150mmof standard FR4 with one connector.
The transmitter converts 10Gbit/s serial PECL or CML electrical data into serial optical data compliant with the 10Gbase-LR standard. An open collector compatible Transmit Disable (Tx_Dis) is provided. A logic "1," or no connection on this pin will disable the laser from transmitting. A logic "0" on this pin provides normal operation. The transmitter has an internal automatic power control loop (APC) to ensure constant optical power output across supply voltage and temperature variations.
An open collector compatible Transmit Fault (Tx_Fault) is provided. TX_Fault is a module output contact that when high, indicates that the module transmitter has detected a fault condition related to laser operation or safety. The TX_Fault output contact is an open drain/collector and shall be pulled up to the Vcc_Host in the host with a resistor in the range 4.7-10 kΩ.
TX_Disable is a module input contact. When TX_Disable is asserted high or left open, the SFP+ module transmitter output shall be turned off. This contact shall be pulled up to VccT with a 4.7 kΩ to 10 kΩ resistor
The receiver converts 10Gbit/s serial optical data into serial PECL/CML electrical data. An open collector compatible Loss of Signal is provided. Rx_LOS when high indicates an optical signal level below that specified in the relevant standard.
The Rx_LOS contact is an open drain/collector output and shall be pulled up to Vcc_Host in the host with a resistor in the range 4.7-10 kΩ, or with an active termination. Power supply filtering is recommended for both the transmitter and receiver.The Rx_LOS signal is intended as a preliminary indication to the system in which the SFP+ is installed that the received signal strength is below the specified range. Such an indication typically points to non-installed cables, broken cables, or a disabled, failing or a powered off transmitter at the far end of the cable.
PIN DEFINITION
The SFP+ modules are hot-pluggable. Hot pluggable refers to plugging in or unplugging a module while the host board is powered. The SFP+ host connector is a 0.8 mm pitch 20 position right angle improved connector specified by SFF-8083, or stacked connector with equivalent with equivalent electrical performance.Host PCB contact assignment is shown in Figure 2 and contact definitions are given in Table 2.SFP+ module contacts mates with the host in the order of ground, power, followed by signal as illustrated by Figure 3 and the contact sequence order listed in Table 2.

PINLogicSymbolName / DescriptionNote1 VeeTModule Transmitter Ground12LVTTL-OTX_FaultModule Transmitter Fault 3LVTTL-ITX_DisTransmitter Disable; Turns off transmitter laser output 4LVTTL-I/OSDA2-Wire Serial Interface Data Line25LVTTL-ISCL2-Wire Serial Interface Clock26 MOD_DEF0Module Definition, Grounded in the module 7LVTTL-IRS0Receiver Rate Select 8LVTTL-ORX_LOSReceiver Loss of Signal Indication Active LOW 9LVTTL-IRS1Transmitter Rate Select (not used) 10 VeeRModule Receiver Ground111 VeeRModule Receiver Ground112CML-ORD-Receiver Inverted Data Output 13CML-ORD+Receiver Data Output (not used) 14 VeeRModule Receiver Ground115 VccRModule Receiver 3.3 V Supply 16 VccTModule Receiver 3.3 V Supply 17 VeeTModule Transmitter Ground118CML-ITD+Transmitter Non-Inverted Data Input 19CML-ITD-Transmitter Inverted Data Input 20 VeeTModule Transmitter Ground1