Anti-Static Anti-Bacterial PVC Vinyl Homogeneous Flooring for Hospital

SPECIAL PUR MAINTENANCE TREATMENT
PRODUCTFEATURES
Eco-friendly: 100% virgin Pure pvc raw material,radioactive elements excluded.
Lightweight: Regular thickness 2.0mm per sqm weights around 3kg/sqm
Wear resistant: Flooing surface treated with UV / PU Coating.
Slip resistant: Special anti slip treatment made on wear layer, to protect the kids & aged safety and avoid slip down.
Fire resistant: Reaction to fire classfication is Bf1 - s1 ,second only to stone material.
Sound barrier: Around 20bd, Noise hardly caused while walking on flooring.
Anti-bacterial: Most of germ & bacterium cant survive.
Water resistant :Raw material are waterproof.
Easy installation: By glue down
Easy maintanence: Cleaning the dirt simply by mop or vacuum cleaner
Specification:
Modelnumber:LS905Material:100% Pure Original PVC materialProductName:homogeneousflooringThickness2mmWidth2mLength20mUsage:Kindergarten, ,club, Office,Schools, Hotels,Nurseries.Dancehall,hospitaletc.Feature:wearresisting,waterproof,non-slip,ShockAbsorption,anti-UV,non-toxicPayment:30%depositinadvance,70%balancebeforedelivery(Paypal,L/C,T/T)Samplesprovidefreesamplesbutyouneedtoaffordthefreight.packagingPapertubeinsideandwaterproofkraftpapercoveredTechnicaldata
TechnicalDataforhomogeneousflooringTechnicalDataTestMethodTestResultsTotalthickness EN428 2.0-3.0mm TotalWeightEN4302850g/m2RollWidthEN4262mRollLengthEN42620mAbrasionGroupEN649TFireRatingEN13501-1Bf1-s1ElectricalresistanceEN1815≤2ToxicTestingGB18586-2001QualifiedDimensionalStabilityEN434sheet≤0.4%ResidualIndentationEN433≤0.1CastorChairTextEN425SuitableColourFastnessIOS105-B02≥6FormaldehydeEmissionEN717-1NDAnti-bacterialISO22196AntibacterialrateLSound-absorbingENISO717/2+4dbCurlingEN434≤8ChemicalresistanceEN423GoodThermalconductivityEN122670.078mmAbrasionresistanceEN660-2≥2mmResistancetoiodineGoodResistancetocarbonpowderGoodResistancetoblackmarkerGoodColor to choose
Factory Show
HOW TO INSTALL AND CAREPREPARATION BEFORE CONSTRUCTIONUnroll and lay the rolls flat for at least 24 hours before installation
ConDITIONS REQUIRED FOR INSTALLATION
1. The minimum temperature of ground should be 10°C
2. The ground must be flat
3. The floor must be dry, The recommended relative humidity inside the room should be 50-60%. The ground surface moisture content must be less than 4.5%.
4. The ground must be free from marks (no felt pen, marker of any type, ballpoint pens, paint, etc., that could cause discoloration due to migration)
5. The temperature of the room should be maintained between 15°C and 28°C
throughout the installation
6. The hardness of ground should ≥C20
LAYING DIRECTION
Plan the sheet direction for the area to be installed to ensure whenever possible that joins do not coincide with doorways, main traffic lanes,
sinks or urinals. If the room is reasonably square, the sheets should run parallel to the incoming light. In long, narrow rooms it is best to install the sheets along the length of the room.
GLUING
Glue with an acrylic emulsion, apply 250 to 300 g/m² using a finely serrated trowel. After allowing an appropriate tack time, press manually using a piece of board with a rounded edge.
WELDING
Hot welding with a welding rod is recommended for rolls and for tiles. Do not weld until the adhesive has bonded completely (wait 24 to 48 hours).
MAINTENANCEAFTER INSTALLATION
1. For the first 24 hours after your new floor is installed protect all the seamed areas and don't walk on the seam sealer.
2. Keep the room at 20°C or greater for at least a 2 days after installation to allow the adhesives to setup properly.
3. Do not roll heavy objects directly on to a newly installed vinyl floor for at least 5 days. This can cause the vinyl and adhesive to become compressed,
once the adhesive sets up any compressed marks will become permanent. Always lay plywood or underlayment to disperse the weight of a heavy objects being moved across your vinyl floor.
4. Allow 5 days before thoroughly washing your floor. This will give time for the adhesive to cure.
Before placing chairs or furniture on your new vinyl floor check the condition of all casters or rollers before setting them on your floor. Replace any worn casters or rollers.
GENERAL VINYL FLOOR MAINTENANCE
1. Dust, sand and grit particles are the enemy. Sweep or vacuum frequently. Don't use a vacuum with a beater bar as it may scratch your floor. And don't use scrub brushes.
2. When sweeping or vacuuming does not remove the dirt, mop the floor with clean warm water. Rinse the floor thoroughly with fresh water..
3. If water alone does not clean the surface, use cleaning products recommended by the manufacturer. Most "no-rinse" cleaners will work just fine.
4. For spots or spills, wipe them up immediately and use the same technique on the spot as you would for the whole floor.
5. If you floor becomes dull looking you may need to add the manufacturer's recommended floor polish to restore the original gloss level.
First, try cleaning with warm water and clear ammonia to see if there is a film on your floor causing the dullness.
6. Never use abrasive cleaners, soaps, paste waxes, or solvents on your vinyl floor.
7. Place non-staining, walk-off mats at every outside entry to your room. This will help keep sand and grit from being tracked on to your floor.FAQ1.Q:Howdoyouguaranteethequalityofyour flooring?A:EachstepisstrictlycontrolledbytheQCteamtomakesureallourproductsturnoutgreat.2.Q:Canyouofferpackingdesignsaspercustomers'requests?A:Ofcourse.Usuallywehaveseveralfixedpackingdesignsforfloortraderstoselect.3.Q:Aresamplesavailable?A:Ofcourse.Asflooringsupplierswearewillingtosupplysamplestoourcustomersfor texting.justtellusthespecifications thatyouneed.