China 155m Bidi SFP Module Fp 20km 40km 1310tx 1550rx 1310tx 1550rx Transmission SFP Optical Transceiver

Product Description

155M Bidi SFP MODULE
GYM67F32-530155Mb/s 1310Tx/1550RxFP 20km
GYM67F52-330155Mb/s 1550Tx/1310RxFP 20km
Features
l Up to 155Mbps data links
l Hot-pluggable SFP footprint
l 850nm Oxide VCSEL laser transmitter
l Duplex LC connector
l RoHS Compliant and Lead-Free
l Up to 20km on single fiber
l metal enclosure, for lower EMI
l Single power supply 3.3V
l Low power dissipation
l Commercial operating temperature range: 0°C to 70°C

APPLICATIONS

l 155Mbps 100base-SX Ethernet
l SDH

The PHF-8524-1LS Small Form Factor Pluggable (SFP) transceivers are compatible with the Small Form Factor Pluggable Multi-Sourcing Agreement (MSA). They are simultaneously compatible with Gigabit Ethernet as specified in IEEE Std 802.3 and Fibre Channel FC- PI-2 Rev. 7.0. They are RoHS compliant and lead-free per Directive 2002/95/EC
I. Pin Descriptions

PinSymbolName/DescriptionRef.1VEETTransmitter Ground (Common with Receiver Ground)12TFAULTTransmitter Fault. Not supported. 3TDISTransmitter Disable. Laser output disabled on high or open.24MOD_DEF(2)Module Definition 2. Data line for Serial ID.35MOD_DEF(1)Module Definition 1. Clock line for Serial ID.36MOD_DEF(0)Module Definition 0. Grounded within the module.37Rate SelectNo connection required 8LOSLoss of Signal indication. Logic 0 indicates normal operation.49VEERReceiver Ground (Common with Transmitter Ground)110VEERReceiver Ground (Common with Transmitter Ground)111VEERReceiver Ground (Common with Transmitter Ground)112RD-Receiver Inverted DATA out. AC Coupled 13RD+Receiver Non-inverted DATA out. AC Coupled 14VEERReceiver Ground (Common with Transmitter Ground)115VCCRReceiver Power Supply 16VCCTTransmitter Power Supply 17VEETTransmitter Ground (Common with Receiver Ground)118TD+Transmitter Non-Inverted DATA in. AC Coupled. 19TD-Transmitter Inverted DATA in. AC Coupled. 20VEETTransmitter Ground (Common with Receiver Ground)1

Notes:
1. Circuit ground is internally isolated from chassis ground.
2. Laser output disabled on TDIS >2.0V or open, enabled on TDIS <0.8V.
3. Should be pulled up with 4.7k - 10kohms on host board to a voltage between 2.0V and 3.6V.
MOD_DEF(0) pulls line low to indicate module is plugged in.
4. LOS is open collector output. Should be pulled up with 4.7k - 10kohms on host board to a voltage
between 2.0V and 3.6V. Logic 0 indicates normal operation; logic 1 indicates loss of signal.

II. Absolute Maximum Ratings

ParameterSymbolMinTypMaxUnitRef.Maximum Supply VoltageVcc-0.5 4.0V Storage TemperatureTS-40 85°C Case Operating TemperatureTA0 70°C Relative HumidityRH0 85%1

Notes:
1. Non condensing.



III. Electrical Characteristics (TA = 0 to 70 °C, VCC = 3.0 to 3.6 Volts)

ParameterSymbolMinTypMaxUnitRef.Supply VoltageVcc3.0 3.6V Supply CurrentIcc 150240mA TransmitterInput differential impedanceRin 100 Ω2Single ended data input swingVin,pp250 1200mV3Transmit Disable VoltageVD2 VccV4Transmit Enable VoltageVENVee Vee+ 0.8V ReceiverSingle ended data output swingVout,pp250450550mV5Data output rise timetr 175ps6Data output fall timetf 175ps6Mask Margin 45%LOS FaultVLOS fault2 VccHOSTV7LOS NormalVLOS normVee Vee+0.5V7Power Supply RejectionPSR100 mVpp8Deterministic Jitter ContributionRX Δ DJ 51.7ps9Total Jitter ContributionRX Δ TJ <65122.4ps10

Notes:
2. Connected directly to TX data input pins. AC coupling from pins into laser driver IC.
3. We recommend <600mV for best EMI performance.
4. Or open circuit.
5. Into 100 ohms differential termination.
6. 20 - 80 %
7. LOS is an open collector output. Should be pulled up with 4.7k - 10k ohms on the host board. Normal operation is logic 0; loss of signal is logic 1. Maximum pull-up voltage is 5.5V.
8. Receiver sensitivity is compliant with power supply sinusoidal modulation of 20 Hz to 1.5 MHz up to specified value applied through the recommended power supply filtering network.
9. Typical peak-to-peak jitter (=6*RMS width of Jitter).
10. Measured with DJ-free data input signal. In actual application, output DJ will be the sum of input DJ and Δ DJ.
IV. Optical Characteristics (TOP = 0 to 70 °C, VCC = 3. 00 to 3.60 Volts)

ParameterSymbolMinTypMaxUnitRefTransmitterOutput Opt. Pwr: 50 or 62.5 MMFPOUT-9 -3dBm1Optical Wavelengthλ830 860nm Spectral Widthσ 0.85nm Optical Modulation Amplitude @ 1.0625 GbpsOMA156 μW2Optical Rise/Fall Timetr/ tf 100150ps3Relative Intensity NoiseRIN -120dB/Hz Deterministic Jitter ContributionTX Δ DJ 2056.5ps4Total Jitter ContributionTX Δ TJ <65119ps5Extinction Ratio @ 1.25 GbpsER9 dB Mask Margin 45%ReceiverReceiver Sensitivity = 1.0625 GbpsRxSENS -20dBm6Receiver Sensitivity = 1.25 GbpsRxSENS -20dBm7Stressed RX sens. =1.0625 Gbps 0.055 mW8Stressed RX sens. =1.25 Gbps-13.5dBm9Average Receiver PowerRxMAX 0dBm Receiver Elec. 3 dB cutoff freq.1500MHz Optical Center WavelengthλC770 860nm Optical Return Loss 12 dB LOS De-AssertLOSD -20dBm LOS AssertLOSA-30 dBm LOS Hysteresis 0.5 dB

Notes:
1. Class 1 Laser Safety per FDA/CDRH, IEC, and EN60825-1 laser safety standards.
2. Equivalent extinction ratio specification for Fibre Channel. Allows smaller ER at higher average power.
3. Unfiltered, 20-80%. Complies with FC 1x and 2x eye mask when filtered.
4. Measured with DJ-free data input signal. In actual application, output DJ will be the sum of input DJ and Δ DJ.
5. If measured with TJ-free data input signal. In actual application, output TJ will be given by:

6. Specifications are for 50 micro-meter or 62.5 micro-meter fiber
7. As measured with 9dB extinction ratio.
8. Measured with conformance signals defined in FC-PI-2 Rev. 7.0 specifications.
9. Measured with conformance signals defined in IEEE 802.3 specifications.

V. General Specifications

ParameterSymbolMinTypMaxUnitsRef.Data RateBR 1.062 Gbps1 1.25Bit Error RateBER 10-12 Fiber Length on 50/125μm MMFL 550
300m2
Fiber Length on 62.5/125μm MMFL 300
150m2

Notes:
1. Gigabit Ethernet and 1x, Fibre Channel compatible, per IEEE 802.3 and FC-PI-2 Rev. 7.0
respectively.
2. At 1.0625 Gb/s Fibre Channel and 1.25 Gb/s Gigabit Ethernet data rates.

VI. Environmental Specifications

PHF-8524-1LS 850nm SFP transceivers have a commercial operating temperature range from 0°C to +70°C case temperature.

ParameterSymbolMinTypMaxUnitsRef.Case Operating TemperatureTop0 70°C Storage TemperatureTsto-40 85°C