China 1830*2440mm Safety Laminated Glass with 0.38mm Clear PVB Film

1830*2440mm Safety Laminated Glass with 0.38mm Clear PVB Film
We are the first whole industry chain PVB related products manufacturer of the world.

Who we are?
Qingdao Jiahua Plastics Co., Ltd . was founded in 1992. And we are the first professional PVB film producer in China. After more than 20 years, Jiahua is at the leading position in the PVB film market based on imported producing lines, rich experience and mature technology. Yearly output up to 8000 Mts.
Qingdao Jiahua not only produce the high qualified PVB film, but also provide considerable technical support for laminated machines by experienced R&D department.
Now Jiahua is engaged in the Research & Production in PVB resin, PVB film, plasticizer, and PVB laminated glass to keep pace with the world market demands. Factory already passed the EN, CE, ISO, SGS as well as the Test Report for PVB products. By conforming to Jiahua enterprise tenet, we hope to cooperate with you for improvement and excellent future!
What is laminated glass?
Laminated glass is a type of safety glass that holds together when shattered. It consists of two layers of glass with a layer of polyvinyl butyral (PVB) film, called the interlayer. It is stronger because of the layering and reinforcement, and when it does break, the plastic essentially acts like tape, holding the pieces in place instead of allowing the sharp shards to fall.

PVB Laminated Glass Specifications:

Product NamePVB Laminated GlassTypesClear/color laminate glass, coating laminated glass, tempered/semi-tempered laminated glass, bulletproof glass, or aquarium glass etc.Float Glass Thickness3-19mmLaminated Glass Thickness6.38-40mmPVB film
ColorClear, milky white,porcelain, grey, blue, green, red, yellow,etc.Thickness0.38-3.04mmSize
Min. Size250mm*350mmMax. Size2440mm*3600mmNoteSize for laminated glass can be at customer request.

Process of laminated glass
Step 1 Glass Surface Preparation
Precise cutting glass and Cutting error must less than 2mm to avoid to occur to bubbles, edge should be grinded. then cleaning the full glass surface and also the final washing with softened water to clean. After in front of process, the cleaned glass can be dried and put it into the bonded glass room to prepare assembly.
Step 2 Assembly
In the bonded glass room, it is cleaned & dust-free and operator should wear cleanly. And also, the temperature should be kept in 15-25ºC and the humidity is in 18-40%. Full pre-laminating process as following:
The first step, lay one piece of cleaned glass on device.
The second step, place the PVB film on the glass and guaranteed the edge of cutting PVB film is 2-5mm more than the each edges of glass. Note to avoid to touch glass with knife when cutting PVB film.
The third step, lay another one piece of cleaned glass on PVB film.
Step 3 De-airing and Edge Sealing
In order to get the well sealed edge, the between the PVB film and the two pieces of glass must expel any air. As usually, there are have two methods to de-airing as following:
1) Rolling De-airing
The pre-laminated glass to heat up to 25-40ºC on glass surface and put it into the first roll by the space of roll is 1mm less than the thickness of laminated glass with pressure in 0.2-0.5 MPa. And also enter into thermostatic container to heat up to 60-80ºC.Then through the second roll by the space of roll is 2mm less than the thickness of laminated glass with pressure in 0.3-0.5 MPa.After finishing to second roll, seal the four sides of laminated glass with clear tape to avoid to entering in air again.
2) Vacuum De-airing
Put the pre-laminated glass into a vacuum bag or vacuum rubber gasket, then use the cool or heat pumping to expel the air. Recommend: the decompression vacuum degree is exceed 650 mmHg. For the cool pumping temperature should be lower than 25ºC and keep it for 30-40mins; while in the period of heat pumping, the temperature should be 70-120 ºCand keep it for 30-60mins.
Step 4 In Autoclave
Put laminated glasses into autoclave and note the space of two pieces of laminated glass is exceed 5mm. Then sealing the autoclave door to raise the autoclave temperature up to 80ºC and then raising rate in 5ºC per minute after temperature 80ºC, and also the pressure in 0.06MPa per minute. When it up to 120-140ºC and 1.0-1.5MPa, keep the temperature and pressure for 30-60 minutes. After that, keep the pressure and lower the temperature to80ºC, at the same time, loose the pressure to the atmosphere pressure. Finishing the high pressure molding process, we can have the final laminated glass for usage.
Why choose us?
1)Jiahua Plastics Co., ltd. is the first corporation of the research, development and production of PVB film in China since from 1992 years.
2) Professional manufacturer
More than 29 years producing PVB resin experience in China and famous brand: "HaoCheng".
3) The non-standard product's thickness and width are welcome.
4) We promise to meet your demands with:
- All products will have been strictly quality checked before packing;
- The raw materials be guranteed by 100% resin;
- Faster lead time (7-12 working days);
- All products will be well packed before shipping;
- Reasonable price with high quality;
5) Assembling of PVB resin, 3GO and laminated glass is also provided;
6) Professional sales term is at your service.
7) Any inquiries will be replied within 24 hours.

Package for PVB laminated glass
Interlayer paper or plastic film between two sheets.
Seaworthy wooden crates
Iron belt for consolidation
Your satisfication is our eternal pursuit.
Regards,
Ms. Wendy Yang
Qingdao Jiahua Plastics Co., Ltd
Mob : +86-138 5420 9824
Tel: +86-0532-86159639
Fax:+86-0532-86158531