China 21 Degree Round Head Zinc Galvanized Plastic Framing Nails for Framing Nailer

For use in 20 to 22 degree plastic collation framing nailers

Plastic collated ring shank

Hot dip galvanized coating resists corrosion and rust. For interior and exterior use. Rated for use in treated lumber

Full round head

21 Degree Round Head Zinc Galvanized Plastic Framing Nails

NameZinc Galvanized Plastic Framing NailDegree28 degree and 17 degree and 21 degreeDiameter2.87mm(0.113"), 3.05mm(0.120"), 3.33mm(0.121")3.76mm(0.148") 4.10mm(1.60")Length50mm-130mmShankSmooth, Ring, ScrewFinishingBright, EG, HDG, DACR, MechGalv, Heat TreatedCoatingYellow, Red, BlueMaterialSteelCustomizedCustomized is available if you provide a drawing or sampleSamplesSamples are freeOEM ServiceOEM Service is available if you provide a drawing or sample.

DescriptionPACKINGPCS/STRIPPCS/CTNMechanicalGalvanized (MG)2.9X50mm252,000MechanicalGalvanized (MG)2.9X65mm252,000MechanicalGalvanized (MG)2.9X75mm252,000MechanicalGalvanized (MG)3.1X83mm252,000MechanicalGalvanized (MG)3.1X90mm252,000 Bright2.9X75mm253,000Bright3.05X75mm254,000Bright3.33X100mm252,000Bright3.8X130mm251,000Bright4.6X160mm251,000 Hot DipGalvanized (HDG)2.9X50mm252,000Hot DipGalvanized (HDG)2.9X65mm252,000Hot DipGalvanized (HDG)2.9X75mm252,000Hot DipGalvanized (HDG)3.1X83mm252,000Hot DipGalvanized (HDG)3.1X90mm252,000 ElectroGalvanized (EG)3.6X25mm254,000ElectroGalvanized (EG)3.6X50mm252,000ElectroGalvanized (EG)3.8X75mm252,000ElectroGalvanized (EG)3.8X83mm252,000ElectroGalvanized (EG)3.8X90mm251,000ElectroGalvanized (EG)4.0x100mm251,000

Smooth Shank

Smooth shank nails are the most common and are often used for framing and general construction applications. They offer enough holding power for most everyday use.

Ring Shank

Ring shank nails offer superior holding power over smooth shank nails because the wood fills in the crevasse of the rings and also provide friction to help prevent the nail from backing out over time. A ring shank nail is often used in softer types of wood where splitting is not an issue.

Screw Shank

A screw shank nail is generally used in hard woods to prevent the wood from splitting while the fastener is being driven. The fastener spins while being driven (like a screw) which creates a tight groove that makes the fastener less likely to back out.

Annular Thread Shank

Annular thread is very similar to a ring shank except the rings are externally beveled which presses against the wood or sheet rock to prevent the fastener from backing out.

Bright Finish

Bright fasteners have no coating to protect the steel and are susceptible to corrosion if exposed to high humidity or water. They are not recommended for exterior use or in treated lumber, and only for interior applications where no corrosion protection is needed. Bright fasteners are often used for interior framing, trim and finish applications.

Hot Dip Galvanized (HDG)

Hot dip galvanized fasteners are coated with a layer of Zinc to help protect the steel from corroding. Although hot dip galvanized fasteners will corrode over time as the coating wears, they are generally good for the lifetime of the application. Hot dip galvanized fasteners are generally used for outdoor applications where the fastener is exposed to daily weather conditions such as rain and snow. Areas near the coasts where the salt content in rain water is much higher, should consider Stainless Steel fasteners as salt accelerates the deterioration of the galvanization and will accelerate corrosion.

Electro Galvanized (EG)

Electro Galvanized fasteners have a very thin layer of Zinc that offers some corrosion protection. They are generally used in areas where minimal corrosion protection is needed such as bathrooms, kitchens and other areas that are susceptible to some water or humidity. Roofing nails are electro galvanized because they are generally replaced before the fastener begins to wear and are not exposed to harsh weather conditions if installed properly. Areas near the coasts where salt content in rain water is higher should consider a Hot Dip Galvanized or Stainless Steel fastener.

Stainless Steel (SS)

Stainless steel fasteners offer the best corrosion protection available. The steel may oxidize or rust over time but it will never lose its strength from corrosion. Stainless Steel fasteners can be used for exterior or interior applications and generally come in 304 or 316 stainless steel.

Contact Us:
FAQ:
1.Q:Do you have your own production factory?
A:Yes,we not only have our own factory,We also have a cooperative relationship with more than one hundred factories in China
2.Q: Can you send us samples?
A: We are pleased to send you the sample to test the quality and market.

3.Q: about your products, could you do it OEM?
A: Yes, OEM service is available.

4.Q: Do you also provide spare parts of pneumatic tools?
A: once we confirm the models you'd like to order, we will send you the diagram for checking and also suggest you some easy-broken parts.

5.Q: For the product, could you spray other color of painting?
A: Yes, color can be customized.

6.Q: What's the delivery time?
A: It usually takes about 20-30 working days to produce one order.

7.Q: How is the payment terms?
A: Normally T/T 30% in advance and T/T 70% before shipment.

8.Q: Can I mix different models in one container?
A: Yes, different models can be mixed in one container, but the quantity of each model should not be less than MOQ.

9.Q: How does your factory do regarding quality control?
A: We always pay great attention to quality control from the very beginning and every product was tested piece by piece before delivery.

10.Q: Do you have quality certification?
A: Yes, we have CE, SGS,ISO, ect.