China 25 Zj Chemical Pumping Slurry From Conditioning Tank to Flotation Cell

25 ZJ Chemical Pumping slurry from conditioning tank to flotation cell

Naipu NP-AH(R) series centrifugal slurry pumps and spare parts can fully interchangeable with world famous brand. These pumps are of heavy duty construction, designed for continous pumping of highly abrasive and corrosive slurries. They feature a wide choice of replaceable abrasion resistant metal or molded elastomer casting liners and impellers, which are all interchangeable within a common casting assembly.
Typical Application-
Mineral Flotation Processing
Electric Factory Coal preparation
Coal Washing
Chemical medium processing
Sand and gravel handling
Effluent Handling
Product Overview:

Pump Parameters

TypeAllowable Mating Max.Power(Kw)Clear Water PerformanceImpellerCapacity/Q m³/hrHead/mSpeed/rpmMax Efficiency/%NPSH/mNos of VaneImpeller Diameter/mm1.5/1NAH1512.6--28.86--681200--3800402--451522/1.5NAH1532.4--726--581200--3200453.5--851843/2NAH3039.6--86.412--641300--2700554--652144/3NAH3086.4--1989--521000--2200714--652456/4NAH60162--36012--56800--1550655--853658/6NAH300360--82810--61500--1140722--9551010/8NAH560612--136811--61400--850714--10568612/10NAH560936--19807--68300--800826576214/12NAH5601260--277213--63300--600773--10596516/14NAH12001368--306011--63250--550794--105106720/18NAH12002520--540013--57200--400855--1051370

Naipu Workshop
Shijiazhuang Naipu Pump Co.,Ltd is a professional manufacturer of Slurry Pumps,
We can be in service from Mould ,Casting, Heat treatment ,Machining, Assembly,Testing etc. one dragon service.
We have our Mould Workshop,there are Wooden Mould,Aluminum Mould,Lost Foam Casting Mould,Wax Mould etc.
Naipu own Casting Workshop,mainly Sand Casting and Lost Foam Casting and Precision Casting.
Naipu own Heat treatment Workshop, after out of furnace,the hardness are according to the technical requirement.
Naipu own Machining Workshop,we are professional from rough machining to finish machining.
Naipu own Assembly Workshop, our mechanicians are skilled in assemblying as we had about 30 years experience in this area.
Naipu own Inspection Workshop, Every order every parts we will do the test before delivery.
Quality Control:
We set various check points along the whole production line,which throughout Raw Material,Charging Material,Surface and Heat Treatment checking,Material Analysis,Spare Testing and Pump Testing etc.
We have established a strict QA and QC system,we can provide quality control records such as "Spectrum Detection" "metallographic Microscope Inspection" "Block Test" "Ultrasonic Flaw Detection" " Penetration Testing"etc. And related test reports to our clients if necessary, such as " Material Test Report " " Dimensional Test Report " " Rotor Balancing Test Report " " NDT Test Report " " Hardness Inspection Report " etc.
Possible Faults and Settlements

Faults Reason Settlement1.Pump fails to discharge any water,The hand of pressure gauge beat violently 1.Suction pipe don't have enough water.
2.Suction pipe blocked or the valve is locked.1. Inject enough water
2.unlock the inlet valve,clear the blocks
3.Exclude the air leakage 2.The pump can't discharge water,the hand of vacuum meter beat heavily. 1.The inlet valve is unlocked or silted up.
2.The resistance of suction pipe is too big or silted up.
3.The height of suction is too high. 1.Unlock the valve or desilting
2.improve the design of suction pipe or desilt
3.Lower the height of the installation.3.The pump can't discharge water,pressure gauge shows heavy pressure.1.The resistance of the discharge pipe is too big.
2.The impeller blocked
3.The speed is slow.1.Check and adjust the outlet pipe.
2.Clear the impeller
3. Improve the speed.4.The pump doesn't rotate The volute is silted up by the blocks. Clear the blocks5.The capacity is not enough 1.The blocks of the impeller or the inlet or outlet pipe.
2.The abrasion of the impeller is heavily.
3.The speed is low to normal
4.Pump is installed unreasonably or the leakage of the inlet pipe.
5.The transporting height is too high,the loss of the resistance of the inside pipe are too big.
6.The inlet valve not open enough or blocked
7.The packing seal leaks1.Clear the impeller or pipe.
2.Change the impeller
3.Adjust the speed
4.Install again or stop leaking.
Decrease the height of the transport or reduce the resistance.Unlock the inlet valve Compress the packing tightly6.The motor of the pump is overloaded 1.The head of the pump exceeds the head of the working condition.
2.Not consider the slurry density when selecting the pump.
3.The packing press tightly1.Turn down the outlet valve,cut the impeller or lower the speed.
2.Select the motor again.
3.Adjust the the screw of the packing gland 7.Abnormal sound in the pump, and no water out1.The resistance of the inlet pipe is too big.
2.The height of the suction is too high.
3.Cavitation occurred there is air in the inletThe temperature of the liquid is too highClear the suction pipe and sluice valve.Lower the height of the suction Adjust the water valve and let the pump operate in the defined limits.Block the leakage.Lowering the liquid temperature.8.pump vibrates1.pump cavitate
2.The block of the impeller single vane
3.The no concentricity between the pump shaft and motor shaft
4.Fasteners or foundation loose1.Adjust the water valve ,lower the height of the installation,reduce the resistance of the inlet.
2.Clear the impeller
3.Alignment again
4.Fasten the screw,and reinforce the foundation.9.Bearing is overheat 1.lock the cooling water
2.lubrication is not good.
3.the lubrication oil is not clear
4.the wrong direction of the thrust bearing.
5.there is something wrong with the bearing.Open the cooling waterAdjust the oil quantity Clear the shaft,change oilAccording to the inlet pressure,adjust the direction of the thrust bearing.Change the bearing 10.Packing short life The material of packing is not good Change the packing 11.pump leak oil1.High oil level
2.The rubber parts invalid
3.Assembly problem1.Lower the oil level
2.Change rubber spares
3.Adjust the assembly
12 Pump head leaking 1.The rubber parts not press wellAssembly again or press tightly

Contact US
Contact Person: Karen Tan