China Air Dryer Heat Regenerated Air Dryer Compressed Air Dryer

JRR series heat regenerative air dryer, it is a new generation of dryer designed on the basis of adsorption dryer! The most important feature is energy saving, heat regenerative air dryer uses the heat generated when the gas is compressed to heat dry The adsorbent in the column desorbs it. When the gas is compressed, it will generate a large amount of contraction heat. The heat regenerative dryer uses this part of energy without the need to obtain heat from the outside world.The heat regenerative air dryer (also known as the compressed heat regenerating air dryer) is derived from the micro heat regenerative air dryer, which has the characteristics of the micro heat regenerative air dryer and has its own unique advantages. The drying device reasonably utilizes the high-temperature heat of the compressor II exhaust gas as the thermal regeneration of the adsorbent, does not require compressed air during the heating regeneration, and only consumes compressed air during the cold blowing, and the regeneration gas is far lower than the micro heat regenerative air dryer. Renewable gas consumption is very low (average gas consumption 1~2%), and it can save energy by 65%. It is an energy-saving air dryer.Features
1. JRR series heat regenerative air dryer adopts the world's most advanced microcomputer controller, can achieve communication and joint control, excellent perfoManufacturing & Processing Machinery rmance.
2. Select high-quality butterfly valve, switch quickly, accurate and reliable.
3. the use of gas diffusion device, uniform distribution of the air flow inside the tower, a unique filling method, long service life of the adsorbent.
4. The waste heat of the air compressor is used in the regeneration process, and the regeneration energy consumption is low.
5. overall layout is reasonable, compact structure, simple installation, easy to use and maintainMeter for Electricity The main technical parameters:
Gas volume: 1-1000Nm3/min
Pressure: 0.2-6.0Mpa
Inlet temperature: 110°C-150°C
Regeneration gas consumption rate: ≤ 1%
Dew point: -50 °C~-70 °C
Pressure drop: 0.03Mpa
Working environment: indoorwork process:
When the JRR series waste heat regenerative air dryer works, the high temperature compressed air first enters the regeneration tower of the drying unit, so that the temperature of the adsorbent is desorbed, and then it is reduced to room temperature through the post-cooler of the drying unit, and finally enters the adsorption tower for drying. When the sorbent of the regeneration tower rises to a certain temperature, the heating is stopped, and 1% of the product gas is used for cold blowing to normal temperature. Since the heat energy generated by the air compression is utilized in the regeneration process of the adsorption tower, the drying device hardly exists. Consumption of other energy, while extending the switching time to more than 300-500min, greatly reduces the operating costs of drying equipment.Equipment composition
JY/JRR series heat regenerative air dryer components: adsorption tower, gas-liquid separator, cooler, electric control box, valves and so on.Operating procedures:
1. Preparation before starting
*Open instrument air supply, control pressure in 0.5-0.6MPa;
*manually detect the action of each valve (manual switch several times);
*Turn on the system cooling water to adjust the flow rate according to the requirements. If the gas in the cooling water system needs to be depleted if it is deactivated for a long time, the next step can be performed after the cooling water is full.
*Turn on the control power and check the process parameters. Each parameter sensor (refer to the process flow and parameter description)
2, the device starts
*Press the device start button to observe the operation of each process valve (each valve).
*The system has a stop memory function. After the restart, the system can continue to run according to the state before the stop. If you want to run again, press the reset button to clear the timing memory.
*Slowly open the compressed air inlet valve, dry the air outlet valve, and let the system pressure slowly rise to the rated value. (If the device does not manually enter or exit the air valve, the dryer can be opened first and the air compressor can be opened again).
3, the equipment is shut down (conditionally choose to stop the regenerative tower regeneration process completion period)
*Stop the air compressor or close the inlet valve and close the outlet valve.
*Press the device stop buAlarm & Security Systems tton to tOther Equipment & Components urn off the main power and turn off the air supply to the instrument.
*Discharge the system condensate and close the cooling water inlet and outlet valves.
*The device is in standby state.Application industry:
JRR series heat regenerative air dryer can be applied to: pCapacitor etroleum, chemical, light industry, textile, fertilizer, metallurgy, electric power, telecommunications, transportation tools pneumatic control,pneumatic components and process gases from various industries provide high quality compressed gas.