China Concrete Cement Additive PCE Powder 98% Tpeg Supplier

Product detail

Concrete/Cement Additive PCE Powder 98% Tpeg Supplier
Three types of powder polycarboxylate superplasticizer water reducing admixtures

1.CL-WRP-98 the powder type of Polycarboxylate superplasticizer water reducing admixture

2. CL-SRP-98 the powder type of Slow release polycarboxylate superplasticizer slump retention water reducing agent

3.CL-PCE-98 dry mixed mortar used integrated polycarboxylate superplasticizer water reducing admixture

Advantages:

New formula,fully reaction, pure appearance

1. High water reduction
2. Low dosage, and so to save cost in comparison with other water reducers at equal performance
3. To maintain slump perfectly
4. To enable a much better flowability of the mixture
5. To improve the strength and durability of the concrete drastically
6. To save cement at equal strength and durability
7. Eco-friendly since no formaldehyde or benzene

Comparison data

(50% mother liquid) tested by Shanlv P.O.42.5 ordinary portland cement,with the dosage of 0.2%

CL-SRP-99:CL-WRP-99=4:6

87g water+0.60g CL-99+300g cement

Time (min)

slump variation retention(mm)

state

30min

240mm

max

60min

240mm

max

120min

220mm

lost

180min

200mm

lost

Notes:

CL-SRP-98 is slump retention admixture . it must used with CL-WRP-99

CL-WRP-98 must be dissolved into liquid about 20% solid content .

CL-WRP-98 and CL-SRP-98 can not been used as dry mix mortar additive.

only CL-98 is a dry mixed admixture.

Do not mix with Naphthalene sulfonate water reducing agent.

Introduction CL-WRP-98

CL-WRP-98 Concrete/Cement Additive PCE Powder 98% Tpeg Supplier

Specifications:

Concrete/Cement Additive PCE Powder 98% Tpeg Supplier
(1) polycarboxylate superplasticizer powder 98% ( please add water to a solid content of 20% before use ).
(2) With a high slump retention ability, without concrete segregation, with a much smaller slump loss than that of other superplasticizers.
(3) With a good dispersion, an excellent adaptability to different cements, and good water-reducing properties. A high water-reducing ratio up to 40% could be obtained when used in high strength grade concrete.(higher than C50). With a dosage of 0.2%,water reducing rate up to 32%.
(4) Cement paste fluidity ≥250mm (with a dosage of 0.2%).
Uses and Cautions:
(1) A recommended dosage is 0.16%-0.4%. Actual dosages should be determined by mixture design test according to concrete strength grade.
(2) 0ºC-40ºC the shelf life of liquid products is 12 months.
(3) Concrete test must be carried out before utilization.
(4) This product is forbidden to be mixed with naphthalene superplasticizers.
(5) Experiment must be done when it is used together with other admixtures.

Item

Specification

Item

Specification

Appearance

powder

Moisture content(%)

≤5

Bulk density(g/l)

≥450

Chloride content(%)

≤0.6

PH Value (20ºC aqueous solution)

10.0±1.0

Water reducing rate %

≥25

Cement paste Fluidity mm

≥240

quick dissolve

Week of other agents

Name

Specification

Naphthalene water reducers

1.Big slump loss

2.Hard to avoid segregation when dosage is slightly higher

3.Certain pollution to the environment as formaldehyde or benzene

Melamine water reducers

1.Air entraining performance is bad
2.Use cost is comparatively high
3.No highlight in its features

Lignosulfonate water reducers

1.Low water reduction
2.The performance is common
3.It's from 1930s, and is coming to be eliminated products. Still used today only for being eco-friendly and people's habit
4.Use cost is comparatively high

Product detail show
Concrete/Cement Additive PCE Powder 98% Tpeg Supplier
Why chose us
Price&supply ability
Concrete/Cement Additive PCE Powder 98% Tpeg Supplier

Price

1.The most competitive price in the world.

2.Finish the payment in global mode or use alibaba credit insurance service.

Supply ability

1.150 containers(1*20') per month.

2.A new order can be prepared and packaged in 2 days.

Package
Concrete/Cement Additive PCE Powder 98% Tpeg Supplier packing as followings:
Main products
Concrete admixture
FAQ
Concrete/Cement Additive PCE Powder 98% Tpeg Supplier
1. Q: Are you a manufacturer or a trading company?
A: We are a manufacturer of PCE in China.
2. Q: Can you provide technical support?
A: Yes, we can provide on line technical assistance or on site technical assistance.
3. Q: How many is your production capacity?
A: We can produce final products 3000 Metric Tons per month.
4. Q: What's your MOQ?
A: 1 Metric Ton.
5. Q: Could you offer free sample?
A: Yes, we can provide sample free for your testing.
6. Q: What's your delivery time?
A: Within 7-12 days after receiving deposit.
7. Q: Could you do OEM or ODM?
A: Yes, we can. We can do solid content 50% or 60%.
8. Q: What's your export port?
A: Qingdao port or you requested.
Contact us
Concrete/Cement Additive PCE Powder 98% Tpeg Supplier
www.bzcljc.com