China Concrete Milling Machine for Removing Paint

Concrete milling machine for removing paint
Description:
1 simple operation, high efficiency!
2 with easy maintenance, power, easy to move and so on
3 to remove the ground coating, paint, a variety of road marking;
4 damaged ground, the need for renovation of the plot, remove the old floor surface;
5 into the quality of heaven and earth, bring unlimited business opportunities
scarifying machine is a light motor drive ground milling machine to 7.5kw kilowatts Y132M-4 variable speed motor as the driving force, the use of forward cutting the working principle, can quickly cut the ground material! Working principle: Unlike the large-scale milling machine's anti-cutting principle, the small milling machine relies on the positive high-speed rotation of the milling drum, so as to shake the six groups of hard tungsten steel alloy blades on the milling cutter shaft. , The use of alloy blade on the tungsten steel alloy teeth to break and ground the ground material, so as to achieve the effect of surface milling;
use:
concrete scarifier machine Mainly used for highway, urban roads, airports, freight yard and other asphalt concrete surface of the excavation renovation, can also be used to remove the road package, oil waves, textures, rutting and other defects can also be used to excavate pits and ditch Groove, and the cement road surface of the hair and the surface of the wrong level of milling.
parameters:

Technical projectmodel:WC-200Gmodel WC-255GPower configurationThree-phase asynchronous motor / 5.5KW (CW200D)
Honda GX270 Gasoline Engine / 13HP (WC200F)Three-phase asynchronous motor / 7.5KW (CW255D)
Honda GX270 Gasoline Engine / 13HP (WC255F) Number of knife shafts6 root6 rootNumber of blades78 pieces (6 teeth)108 pieces (6 teeth)Bearing seal formSealed (maintenance-free)Sealed (maintenance-free)A milling width200mm250mmA milling depth3mm-5mm3mm-5mmweight90kg115kgLong x wide x high1125x500x1125mm1125x500x1125mmHourly work efficiency150 square170 squareWalking wheel4 only4 onlyAir damping tube2 only2pcCounterweight 25kg(standard)

4. concrete scarifier machine use and maintenance
1 machine is the main part of the work due to milling cutter, bearings, gaskets, milling drums, the operation process due to a long time with the road friction, the fastest consumption is this part of the regular replacement, inspection in order to better extend the use of the machine life;
2, milling cutter shaft should be checked daily, if the above grinding out of the slot more than 25% of the diameter of the knife, you have to replace. In general, the life of the knife shaft is half the life of the tungsten steel cutter. scarifying machine From the square area, the life of the milling depth of 5mm when about 350-500 square meters. But please pay attention to, there are many factors that will affect the life of the knife shaft, so to check every day;
3, for safety reasons, before the maintenance, should first pull the engine spark plug, preferably by the qualified mechanic;
4, each time before running to check the oil level, after use to clean the air filter;
5, every 4 hours after use, to grease the bearing. concrete scarifier Hit the grease, while playing side of the rotation drum, so that grease coated in the entire bearing;
6, before each operation with the naked eye to check the machine: all fasteners are tightened? Are there any parts of the obvious wear or cracking? Oil pipeline is intact? Check the bearings, check the cover is covered;
7, before each operation, to check the belt tightness. The new belt should be reoriented after 4 hours of operation, and the belt tension must be maintained in order to transmit the output horsepower of the engine to the cutter drum. scarifier concrete grinder When the tight belt is too tight, the belt will be easily worn and the bearing life will be shortened , If broken, serious wear and tear of the belt should immediately change the new; forget the past to have a new start.
8, in general, milling cutter cracking is very rare, if any, usually shows the following: a: milling cutter on the irregular arrangement; b: a single milling too deep; c: the use of inappropriate milling Knife to remove the different types of road; d: milling the surface strength is too large; to be courage to admit their mistakes, and bear the responsibility.
9, each time you change the milling cutter arrangement, check the cutter shaft and the bearing. If the shaft appears to wear the groove, you need to replace the new, when the axis for the same time for bearings;
10, milling drum if properly maintained, usually can be used for 3 months. When checking the milling cutter or doing maintenance, check whether there is any cracks in the center axis of the milling drum, whether the sleeve hole is oval, whether there is any crack at the weld, and if there is any damage,
11, and finally, when you want to check the milling machine at the bottom of the milling machine, reminded that: the machine must be tilted forward, never backward, or oil will pour into the engine cylinder.

ModelZT70ZT100ZT120Drill Diamterφ60-80mmφ83-100mmφ85~130mmRock hardness≥20≥20≥20Drill Depth≥15m≥3030-40mSwing speed110r/min90r/min90r/minAir pressure0.5-0.7Mpa0.5-0.7Mpa0.5~1.0MpaAir consumption≥3.5m3/min6M3/min10m3/minCylinder Diameter90mm90mm90mmValid Distance1070mm1070mm1200mmPropulsion3600N6000N9600NPower3kW3kW3kWVoltage380V380V380VRated speed1410r/min1410r/min1410r/minOuter Diameterφ42mmφ42mmφ42mmDrill Pipe Length1025mm1025mm1025mmSize1740x260x420mm1800*650*400mm1800*700*450mmWeight220kg250kg300kg

FAQ:
Q1: Are you factory or trade company?
A1: We are factory. And we have ourselves trading company.

Q2: What the exactly address of your factory?
A2: No.27,Beichen Village Industrial Park, Weiyang District, Shaanxi Province China.
Q3: Warranty terms of your machine?
A3: One year warranty for the machine and technical support according to your needs.
Q4: Will you provide some spare parts of the machines?
A4: Yes, of course.
Q5: What about the voltage of products? Can they be customized?
A5: Our standard voltage is 380V, 50HZ, 3phase. The voltage can be customized according to your equirement.

Q6: Which payment term can you accept?
A6: 100% T/T( Decide according to actual situation)
Q7: How long will you take to arrange production?
A7: we can delivery the normal goods within 7-15 days. Other nonstandard electrical items we will delivery within 25-30 days.

Q8: Can you accept OEM orders?
A8: Yes, with professional design team, OEM orders are highly welcome.

Q9: Which trade term can you accept?
A9: Available trade terms: FOB, CIF, CFR, EXW, etc.
Q10: Do you provide samples? Is it free or extra?
A10: Yes, we could offer you the sample machine. But it's not free. You need to pay for the sample and the cost of freight.
Q11: What is your terms of payment?
A11: We accept T/T, Western Union, Money Gram, Paypal, L/C, etc.

Our Company Information:

We have been focusing on high-quality mechanical equipment and construction products for more than 20 years. Especially have rich experience at mining equipment, main products include:
Ultra Large Rock Splitter
Submersible Drilling Rig
Spraying Machine
Grinding Machine
about Our Factory:

about the products:
Packing and Shipping:

Purchase Process:

about the Quality:

Others:
Why you choose us:
1. We are a real factory offering products and provide free technical advice.
2. Company in business for many years and served Over 50 countries customers.
3. All machine with CE, ISO,SGS certificate. Machine and spindle warranty 1 year.
4. We have phone support in English, if you have any questions, you can call us, and we can give you the best solution within 24 hours.
5. Fast delivery, save your time.
Contact us: