China High Frequency RFID Reader 13.56 MHz Rfh-1332-114b

High Frequency RFID Reader (13.56 MHz)
P/N: RFH-1332-114B
1.Overview
The RFID (Radio Frequency Identity) RFH-1332-114B is a non-contact high frequency RFID reader, specially designed for use in embedded applications such as address reading or proximity control of AGV and other industrial application. It can be worked in a variety of harsh environments. The RFID reader has anti-collision function, its operating frequency is 13.56MHz.
2. Key Features
Comply with ISO 15693 Protocol and ISO/IEC 18000-3 Protocol; ISO14443A protocol.
Support NXP I. CODE SLI and other tags Comply with the ISO15693 Protocol.
Support reading and writing, without data misread.
RS232 with Cable(1.0M long), RS485 and Ethernet (TCP/IP) can be selectable.
Built in RFID antenna (Integration Design of Reader and Antenna)
Read / write distance 70-90mm (industry Environment), reading time is less 20ms /8bit.
Good package IP65, PBT engineering material suit industry environment application
3. Applications
Address reading or proximity control of AGV,forklift and industrial production line material identification application.
4. Technical Data sheet

Operating Frequency13.56MHz Working Voltage10-30VdcWorking current<0.2A Standard Interface ISO/IEC 15693 and 14443ACompliance interfaceISO18000-3 modeMaximum Reading distance70-90mm Reading time20ms/8 bitRadiation Power 2W InterfaceRS485; TCP/IP(option) Indication 2 LED (Red LED for power, Green LED for working )Working Temperature -20ºC~+70ºC Storage temperature-20ºC~+85ºC Working humidity<95% Cable5 core shield (800mm) or (M12 option)Color of HousingGreen HousingMaterial of HousingPBT+ABSDimension As attached drawingIP classIP65 Industry Environment

5. Dimension and picture

Installation location dimension:4-φ3mm*6mm
6. Wiring Diagram

Cable numbercolorPin configure2BrownVin9-30vdc4BlueGND1WhiteTX 5GreyRX

7. RFID Sensor with Host Computer Communication Data Packet Format
This data message format is used for communication between the RFID (HF) sensor and the host computer (controller). The host computer sends commands (downstream) and the RFID sensor responds (upstream). The communication port baud rate is 9600, data is 8 bits, no odd check, stop bit is one bit.
Command format

frame header
01Data lengthData1Data2…Data NChecksum (CAL)End of frame
FD

Data length:The length of the Data1~Data N(=N);
Checksum(CAL):From the data length to Data N (N+1 number) sum, take the lower 8 bits.
Note:The data is a hexadecimal number in the table.Start to read tagStop reading tagReading 15693 tag data

010242478BFD

010245448BFD

01035452Block number
(0-1bit) CALFD

Respond

0104XXXXXXXXCALFD

Where from 3 to 6 bytes are read data (4 bytes).Writing 15693 tag data

01075457Block number(0-1bit) XXXXXXXXCALFD

Where from 6 to 9 bytes are written data (4 bytes)
Respond (success)

01045355434332FD

Reading Mifare tag data(S70 card)

01034D52Block number
(00-3F)CALFD

Respond(success)

0110XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXCALFD

Where from 3 to 18 bytes are read data(16 bytes).Writing mifare tag data(S70 card)

01134D57Block number
(00-3F)XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXCALFD

Where from 6 to 21 bytes are written data (16 bytes).
Respond(success)

01045355434332FD

Instruction:The RFID sensor automatically reads the card when it is turned on.The RFID sensor reads the data stored in the tag automatically when the tag is in reading area. The RFID sensor stops reading the card automatically after receiving the command to stop reading; and it can be restarted read the card after receiving the reading card command.when the mifare tag is used, block cannot be read and written with block numbers 3+4+n (n=0, 1, 2...), In other words, the blocks cannot be read and written with blocks numbers 3,7,11....