Cartridge Heater, Cartridge Heating Element, Cartridge Heating Rod manufacturer / supplier in China, offering Customized High Density High Power Electric Heating Element, Spring Hot Runner Coil Heater, Coil Heater for Plastic Injection Moulding Machine and so on.
Min. Order / Reference FOB Price | |
---|---|
10 Pieces | Contact Supplier |
Local Area: | Shenzhen, Guangdong, China |
---|---|
R&D Capacity: | OEM, ODM, Other |
Payment Terms: | LC, T/T, PayPal |
Certification: | RoHS, ISO9001, CE |
---|---|
Type: | Silicon Heater |
Material: | Sic Content |
Outer Diameter:OD, (mm) Hot Zone Length: HZ, (mm)
Code Zone Length: CZ, (mm) Overall Length:OL, (mm)
Shank Spacing: A, (mm)Bridge: D, (mm)
Note: Specification above are parts of our products for your reference, and we can manufacture according to your special specification.
Detailed Images
Our Service
1.Timely response
Timely response to your inquiry,multiple choice recommendations based on your demand,quickly respond mails and provide solutions.
2.Professional Services
Provide high temperature solutions and professionals construction services according to our experience.
Provide all the detailed news and pictures from order to delivery;
Provide the most reasonable logistics for customers to save every penny.
Offer relative export documents and original certificate if needed;
Warm and considerable after-sale service.
3.Strict quality control
Arrange production on time and control quality strictly.
4.Shorter delivery time
Book the earliest vessel or plane to guarantee the delivery time.
Packing & Delivery
SiC Heater Package: Wood Box Padded With Foam Board
Delivery Time: 7-20 Days
Installation
1. In order to keep the furnace temperature and the charges uniform of each element, resistance value must be matched first before installation, arrange those with close current values on the same circuit.
2. As the heating elements are made of ceramic, avoid damage from mechanical shock.
3. The diameter of a piercing hole drilled through the furnace should be about 1.5 times the diameter of element's end section. Size under 20mm is suitable for brick layers up to 150mm in thickness. Size under 25mm is suitable for brick layers up to 250mm in thickness.
When brick layers are thicker than the above thickness, widen the piercing hole diameter more 5mm.
When SG type element is used, take 5mm more margin than the above value.
4. Silicon Carbide elements are electrically conductive. Care should be taken to avoid electric leakage due to direct contact with a conductive material or electric shock to a human body.
5. An equal length of element's cold zone should protrude out of the furnace. Elements should be installed so that the heating section( hot zone) does not intrude into the furnace wall. Install the elements at the center of the piercing hole, and lightly pack ceramic fiber around the element.
6. Make sure that neither the terminal clamp nor the terminal strap will contact the furnace wall directly. The terminal strap must have enough slack to give under finger pressure.
7. After completing connections, turn on electricity after lightly pressing the heating element with a finger tip and make sure it will move easily.
8. When replacing elements, it is recommended to replace all heating elements in the same circuit, otherwise the resistance difference new and old elements can cause a load imbalance. This imbalance results in the newer elements' loading being greater which could shorten its service lift. It is recommended that older, or " aged" elements be used on the same circuit.
9. When start to run the furnace, raise voltage slowly and gradually never give full load at one time, otherwise, the heating element will be damaged by over current impulse.
10. As the resistance of all silicon carbide elements increases during use a variable voltage power supply is usually provided. The power supply may consist of a step transformer, thyristor, or a combination of both. The type of equipment used may effect the element performance and therefore the necessary appliances shall be selected carefully.
11. Before use the new furnace or the furnace that has not been used for a long time, they must be dried. While drying, it better to use old elements or other heat source.
12. While sinter products or materials, if there is water ejection, the furnace should have holes to eject water vapor or other waste gases in order to protect the elements service life.
If you have any question or special requirement, please do not hesitate to contact us, we are always here for you.