China Rdj1250 2000- 2001400 Type Hot Isostatic Press

RDJ500/1500-200.2000 Type Hot Isostatic Press

Main Technical parameters

Maximum working pressure: 200MPa;Maximum working temperature: 1400ºC;Common operating temperature: 1300ºC;The effective diameter of heat zone: Φ1250mm;The effective height of heat zone:2000mm;Heating wire material: Molybdenum-Lanthanum alloy; Vacuum degree(cold state, no working parts): ≤500Pa;Vacuum time(cold state, no working parts): t≤30min; Working medium: Ar (Purity≥99.99%);Maximum temperature deviation of effective hot zone from 700ºC to 1300ºC(no working parts,Heat preservation stage, pressure ≥30MPa):≤±10C;Heating up time:≤3h(no working parts,room temperature~1300ºC);0~60MPa Prepressurized time(no working part):≤3h(as the temperature rising to 1400ºC, the pressure natural expansion reaches 200MPa).Gas recovery rate:≥80%;Loading mode:upper loading;Install way: Pit installation

Operating conditions

Altitude: ≤2000m;Temperature:+5ºC~+40ºC;Relative humidity of air is not more than 90%(when room temperature is 20ºC);Power supply requirement:AC380V ±10%,50Hz ±1%,TN-S income wire system( Three-phase five-wire system);Outlet circulation water supply requirements:Flow≥80m³/h, Pressure0.3~0.5MPa, Water inlet temperature ≤30ºC,Water outlet temperature≤45ºC;The working limit height of the crane hook in the workshop of the hot isostatic press is from the ground≥7m,the hoisting weight≥20t;A place free from fire,serious pollution,chemical corrosion,violent vibration and strong disturbance sources.The weight and dimensions of the main components are:Yoke frame (2 sets):about 129t per set, each size 4180mmX 810mmX 9435mm;
Vessel :about 150t, size 2700mmX 2700mmX 5045mm;
Our main type of press is as follows:
1. Cold Isostatic Press:

S.NO.TypeDiameter of Pressure
VesselDepth of Pressure
VesselMaximum Isostatic
Pressure1CIP 200/300-300200mm300mm300Mpa2CIP 200/1000-300200 mm1000mm 300Mpa3CIP 420/4000-320420mm4000mm320Mpa 4CIP 500/1200-400500mm1200mm400Mpa5CIP 500/1500-300500mm1500mm300Mpa6CIP 710/2000-250710mm2000mm250Mpa7CIP 1000/3500-2001000mm3500mm200Mpa

a. The vessel inner materials is 34CrNi3MoV alloy whole parts forged and then The forged vessel be wire wounded by alloy of wire(65Mn steel 1.5mm x 6mm size) as per the designed.
b.Whole procedure of the cold isostatic pressing (CIP) machine, increasing, holding and releasing pressure is controlled by PLC and also there is a decompression system to protect the system over pressure to keep the machine in safety running
2. Hot Isostatic Press:

S.NO.TypeDiameter of
Pressure VesselHeight of
Pressure VesselPressureTemperature1HIP 800/1200-150/1000800mm1200mm150Mpa1000degrees2HIP 1250/2000-200/14001250mm2000mm200Mpa1400degrees

3. Warm Isostatic Press:

S.NO.TypeDiameter of
VesselLength of
VesselPressureTemperature1WIP D500-L2000/P200mpa-T300500mm2000mm200Mpa300degrees2WIP D300-L1500/P250mpa-T200300mm1500mm250Mpa200degrees3WIP D630-L2000/P250mpa-T300630 mm2000mm 250Mpa300degrees

a.The vessel inner materials of WIP is 34CrNi3MoV alloy whole parts forged and then The forged vessel be wire wounded by alloy of wire(65Mn steel 1.5mm x 6mm size) as per the designed.
b.Whole procedure of the warm isostatic press machine (WIP ) , increasing, holding and releasing pressure is controlled by PLC and also there is a decompression system to protect the system over pressure to keep the machine in safety running.
Contact Us:

Marketing Manager: George SunTel:+86 13401926888
+ 86-25-84508704 Website:chinasun99.en.made-in-china.com Address:88# Zhujiang Road,Nanjing,Jiangsu,China