Electrostatic Powder Coating Flocking Machine Painting Equipment

Product Display
Technical Data
Input Power: 50W
Input Power Voltage: 110V-120V AC, 220V-230V AC
Output power voltage: 0 ~100KV
Output Current: 0~150uA
Weight of Gun: 480g
Length of Gun Cable: 4m
Stainless Steel Powder Hopper Capacity: 55L
Work temperature range: -5° C to 40° C
Payment & Shipping terms
Delivery Time: Usually5-7days (According to the order quantity)
Payment Terms: T/T, Paypal, Western Union
Price Terms: FOB, CIF, CFR
Supply Ability: 100 sets per week
Weight: 26kgs (Packing with Carton)
Main data:
Input voltage: AC180V-240V/50HZ
Output high voltage (gun): 0-110KV
Input power: 40W
Weight: 30KG
Air pressure: 0.5Mpa-0.8MpaMain configuration:
Spray gun * 1 +powder pump * 1 + host * 1+ powder hopper* 1 + trolley * 1 + air pressure control valve * 1+ oil water separator * 1
HostFor the powder and gas sourceSpray gunInput voltage: 200-240v 50HzSolenoid valve control voltage: 24VDCInput pressure: ≤0.3MpaInput powder: 50WInput pressure: 0-0.6MpaThe volume of the powder: max550g/minOutput pressure: 0-0.5MpaOutput voltage: 0-100KVThe largest gas consumption: 13.2m/h (0.4Mpa)Output current: 0-200uAVolume of powder barrels: 50LGun weight: 460g
Advantages
1,High voltage module near the nozzle, make waste less voltage, high voltage components can be replaced, brings convenience to maintenance.
2,Low rotary atomizing air, greatly improving the coating quality.
3,Intuitive for powder reasonable two-way flow meter display.
4,Low because chooses big flow pneumatic components in smaller airflow pressure, still can achieve higher amount of powder.
5,For powder device is full stainless steel, can need not tools can easily remove and clean all parts.
6,Two lines of the design of the central gas, make a needle guide body no longer product powder, strengthened the discharge effect, improve the rate of powder.Operating Instruction:Connect all the connecting lines and air tubes.Turn on switch of power supply (lighting indicator is on).Press the switch of spray gun to adjust voltage required (set by individual, voltage recommended is 60KV-80KV).Powder is placed into powder feeding barrel.Press the switch of spray gun and adjust to high-voltage. Start work if the powder is sprayed.
Attentions:Grounding line is attached with the equipment and must be connected with the spray booth, which is to be connected with special clean ground. Workpieces, hanging articles and support must be connected with grounding line to prevent grounding failure from making discharge sound.All compressed air must be kept tidy and dry, and has no oil or water. It is recommended that the customer use frozen and dried air sources. If the customer uses general oil-water separator, the oil and water must be regularly discharged in case that the coating ratio will be influenced by water accumulation in air box of powder barrel, solenoid valve and air tubes or too much humidity.If abnormal powder spray (i.e. bigger or smaller from time to time) happens to new equipment, generally that's because powder feeding and lending air pressures are not properly adjusted. Powder spray increases as powder feeding air pressure increases. Adjust the powder blending air pressure to a higher level to ensure that powder spray is in uniform.Powder pump and spray gun should be blown and tidied up with compressed air after they are used for some time.Pressure regulating valves own locking device, in which "Push" means "off", "Pull" means "on". The buttons of various regulating valves should be adjusted to proper position (as is to be indicated by satisfactory powder spray).
Check the following conditions if the air pressure is not enough:Whether the air pressure in compressor is more than 6kg.Whether there is a leakage in the air tubes.Whether pressure regulating valves are in good condition. Generally the pressure regulating valves are easy to adjust, anticlockwise direction to the end (off) or clockwise direction to the end (maximum). Do not regulate them violently. If the pressure can't be adjusted to a higher level, the equipment will not be used until relevant solutions are found and failures are repaired.our warehouse:Our package
POWER EQUIPMENT
OUR COMPANY
Qidong huakun spraying equipment Co., Ltd. is a professional powder electrostatic spraying equipment manufacturers. Its performance is superior, the powder is large and uniform, the powder rate on the dead Angle is high, has the better practicability to the metal powder. It is widely used in metal surface treatment industry. Through the efforts of all the staff and the support of customers at home and abroad, the products have been constantly updated, improved and diversified, and now has developed into a collective r & d, production, trade and one of the coating equipment manufacturers. Our philosophy: quality first, reputation first.
The company has a well-trained, high-quality staff and a number of outstanding technical personnel committed to research and development. The company has a set of advanced production equipment and testing equipment, and the introduction of foreign advanced technology. The product selects the import component, guarantees the product quality to be stable. Customers all over the country or even the world, the products are exported to Spain, Africa, the Middle East, Vietnam, Russia, southeast Asia, Hong Kong, Taiwan and other countries or regions.
Main products:
Our strength: Factory price, OEM/ODM, Highest quality, Fast delivery, best after-sales service. Our company's philosophy for the majority of new and old customers to provide quality products and sincere service quality; We look forward to your joining us and starting a business together.