High Speed Stud&Track Channel Roll Forming Machine

FactoryProduct overview:
Our factory is specialized in different kinds of roll forming machine ,also we can design the machine according to you products details :Roofing and wall panel roll forming machine,Glazed tile roll forming machine,Roof ridge cap roll forming machineShutter door roll forming machine,Pu foam shutter door production line,Door frame roll forming machineCeiling keel roll forming machine,Tee grid roll forming machine,C&Z purlin roll forming machineFloor decking roll forming machine,Pipe roll forming machine and bending machineGutter roll forming machine,Guardrail roll forming machine,Stone coated steel tile production lineSandwich panel production line,Slitting line,Curving machine,Decoiler,Cutting and bending machine__________________________________________________________________________________________________________
high Speed Stud&Track Channel Roll Forming MachineComposition of roof roll forming machine
A. Uncoiler.......................................................................1 unit
B.Main roll forming machine ·································· 1 unit
C. Control panel·····················································1 unit
D. Accepting table..............................................................1 unit
E.Hydraulic pump...............................................................1 unitDetails of each roll forming machine composition:uncoiler ( one manual for free )
(1) 4 feet manual uncoiler
(2)Capacity of the uncoiler : 5 tons
(3) Range of segment expansion : 460 ~ 515 mm
(4) Inner diameter of coil : 508mm
(5)Maximum width of coil : 1300mm
variety of styles to meet different requirements
Main roll forming machine
1. Forming stations : 13stations
2. Material of roller : Cr12heat treatment HRC60 and surface is being hard chrome;
3. Shaft : Dia 80mm, high frequency surface treatment and grinding process;the material is 45#steel.
4. Horsepower : 5.5KW(The motor is used to drive the hydraulic pump ,which enables the hydraulicoil to drive the hydraulic motor and then drives the main machine.)
5. Transmission : Chains and gears
6. Forming speed : 50M/MINUTE
7. Forming thickness : 0.2 -0.7mm
(1) High tensile coil is used, Yield Strength: 550MPa or less
(2) The finished products will change if using different material and thickness.
8. Cutting:
(1) Flat-sheet cutting: It is used when changing the coil of raw material; it
can cut the coil rapidly and time- saving.
(2) Cutting after forming: Cut the sheet after roll forming to required length
(3) Cutting motion: No-stop cutting with the seivo motor
(4) Material of blade: Cr12; heat treatment HRC59~61
(5) Length measuring: Automatic length measuring
(6) Tolerance of length: +/- 1.5mm
9. Approximate Size: Length: 4M * Width : 1.0M * Height : 1.3M
10.Characteristics of the main machine
(1) base is made of high tensile strength H beam with precision welded and
good rigidity.
(2)Shaft, roller and all components are manufactured precisely to have long
lifetime.
(3)Efficient design, easy maintenance
Control panel
(1) Voltage, Frequency, Phase:Customizable
(2) Automatic length measurement: one unit tooling of length measuring
which is lightly pressed on the surface of the steel sheet; the tolling will roll
with the moving speed of the steel sheet and then sense to measure its length.
(3) Automatic quantity measurement
(4) PLC is used to control length & quantity. Machine will automatically
cut to length and stop when required quantity is achieved
(5) 99 kinds of dimensions can be set in one order at the same time,
continuously production and nine orders can be keyed-in at a time.
(6) The total length of the order is automatically counted; when the
material's supply is enough, the material will automatically stop entering the machine which is the convenient device for orders (with different material) to change the material.
(7) Length inaccuracy can be amended easily.
(8) Control panel: Button-type switch, LED display length and quantity
(9)Unit of length: millimeter and inch (switched on the control panel)
(10) Motor Over-Load protection
(11) System Over-Current protection
(12) Short circuit protection
(13) Display total length produced
(14) Display total quantity produced
Hydraulic pump
Hydraulic system for cutting
The motor is used to drive the hydraulic pump ,which enables the hydraulicoil to drive the hydraulic motor and then drives the main machine.
Accepting table (one manual for free)
lenght :4m__________________________________________________________________________________________________________Our Service:Pre-Sales ServiceOur factory has 15 years of production experience, experienced technical department will be based on your specific drawings and requirements to design machines, and give you the appropriate technical advice
* Inquiry and consulting support
* Sample testing support.
* View our Factory.After-Sales Service
* Training how to instal the machine, training how to use the machine.
* Engineers available to service machinery overseas.
Packing & DeliveryPackagingPacking method: nude, with waterproofcloth and stow-wood. The computer controlled cabinet is packed with waterproof cloth and box. The seller should guarantee equipment will be moisture-proof, anti corrosive, and will not be damaged during transportation.
__________________________________________________________________________________________FAQ:
1. Does one machine can only produce one style panel profile?
Not exactly.For wider and double layer making machine. It can produce more than 6 kinds of panels.2. Do you have after sales support?
Yes, we are happy to give advice and we also have skilled technicians available across the world.We need your machines running in order to keep your business running.3. How to visit your company?
a.Fly to Beijing airport: By high speed train From Beijing Nan to Cangzhou Xi(1 hour), then we can pick up you.b.Fly to Shanghai Airport: By high speed train From Shanghai Hongqiao to Cangzhou Xi(4.5 hours), then we can pick up you.4. How to get a quotation?
a. Give me the profile drawing and thickness, this is the important. If no,I will suggest you some.
b. Other specific requirements are welcome, such as the speed, power and voltage you want.5. What can you do if the machine broken?
Our machine's warranty period is 12months! If the broken parts can't repair, we can send the new parts replace the broken parts free. If after warranty period,we can through negotiation for to solve the problems, and we supply the technical support for the whole life of the equipment.6. Can you be responsible for transport?
Yes, please tell me the destination port or address. We have rich experience in transport.7. You are trade company or factory?
We are factory. Welcome to our workshop for visiting.
8. How long the machine could be made?
Normally speaking, common roof profile roll forming machine could be made within 45 working days.
If you need machines in a hurry, we can make it for you less than a month.If need more machine pictures or videos,welcome to contact me.