Multi Shot Electronic Inclinometer for Oil Drilling / Exploration Drilling

Multi Shot Electronic Inclinometer for Oil Drilling /Exploration DrillingProduct description:1. Intuitive operator interface.
Users do not need manual can prompt completion of all the features provided by the probe according to the probe panel, simple operation, intuitive and fast.2. Embedded powerful direct reading.
Without ground instrument with the probe can be done alone display of the parameters, settings and printing. Eliminating the need for ground instruments, greatly save the time of measurement.3. Assured smart reminder.
The intelligent reminder feature real-time detection of various states of the probe in the work, and to detect the fault and display. For the user to ensure that the instrument is normal to go down before.4. Acceleration sensor and magnetometer. Global advanced MEMS process.
Advantage of MEMS technology, the probe can provide high-precision measurements in harsh working environments, and other low power MEMS process the probe has alonger working time. Work environment and low power consumption are the traditional mechanical sensors can not match.5. Unique momentary power failure from the restore function.
Completely avoided in the process of the instrument downhole, and instantaneous power interruption caused by ashock, vibration and cause the failure of the measurement. Probe to restore the original state of the work.6. To meet avariety of practices.
Meet hanging measured with different underground protection assembly voted measured, the job requires aself-floating way.7. Measuring range and accuracy.ProjectMeasuring rangeMeasurement AccuracyRestrictionsBorehole Deviation0~180°±0.1°/Magnetic Bearing0~360°±1°Borehole deviation≥6°High-Side Tool Face0~360°±0.5°Borehole deviation≥6°Magnetic Tool Face0~360°±1°Borehole deviation≤8°
8. Single multi-point integrated design.
Roschen multi-point probe by the probe panel, the choice of asingle multi-point work. Actually equivalent to the user to purchase two of the probe. Single point probe measurement in drilling when drilling is completed with multi-point probe tube pulled out the well-rail. Save user investment.
9. Technical indicators:
Temperature: -40ºC~125ºC (with insulation protection assembly, the maximum operating temperature of 250ºC);
Vibration: frequency 10 ~100Hz, vibration acceleration ≤4.5g, half-sine;
Shock: Shock ≤2000g, 0.5ms;
Operating voltage: DC6V ~DC8V;
Working current: DC5V power supply conditions, standby operating current ≤30mA acquisition operating current ≤150mA;
Operating temperature: -40 ~125ºC;
Impact resistance: 2000g, 0.5ms;
Vibration resistance: 10g, 20 ~100Hz;Dynamic performance:
the acceleration of the vibration conditions 3g, frequency of 20Hz, borehole deviation measurements with static measurements, borehole deviation error ≤0.2°;Delay time range:
1 to 99 minutes, the minimum delay of 1minute;Interval range:
1 to 99 seconds, minimum interval of 1second (only applicable to multi-way);Maximum sampling points:
3600 points. (only applicable to multi-way);Continuous working time:
more than 20 hours (only applicable to multi-way).Multi-shot Inclinometer:
The user may use '←'or'→' on the panel to choose 'S'(Single Shot) or 'M'(Multi-Shot) when the two buttons flickering. Press '/confirm/i' for /confirm/iation. The tube will be ready for aworking mode when the choice for single shot or multi-shot is made, which will be confirmed by the stop of flickering of the button 'S' or 'M'.For re-select aworking mode, the removal of battery barrel is required.1. Connection of the external protection component
Under the mode of directional measuring, tie the steel rope on the Socket head and bolt the Rubber protector on the Brass connector. Then connect the following parts according to the Figure 4-4, rope socket head, circumrotate hanger, radial buffer, brass connector and external protecting barrel. Install the lead seal on the guide shoe.
Under the mode of non-directional measuring, connect the bottom buffer, radial buffer, multi-buffer, extended bar and brass connector according to the figure 4-5. Bolt the rubber protector on the brass connector tightly. Then connect the external protecting barrel. Remember to tighten each connecting part with rubber pipe spanner. Put the steel rope through the hole of the rocket head and tie up. Bolt the rubber protector on the brass connector tightly. According to the figure 4-5, connect the rope socket head, circumrotate hanger, radial buffer and brass connector.
2. Assembling
In directional measuring
Hang the T-head of the probe-tube on the directional buffer connector. Then put them into the external protecting barrel.Tighten the directional buffer connector and install the lead seal on the guide shoe.
In non-directional measuring
Hang the battery barrel on the rubber hanger and hang the T-head on the rubber protector. Put them into the external protecting barrel and bolt the brass connector. Tighten each connecting part with rubber pipe spanner.3. Data ReadingSee 4.3 step 5self-floating mode.Cautions:
Ø The voltage of battery must be higher than 4.8V before the inclinometer is put into the well.
Ø In directional measuring, high side correcting must be performed. If the directional part of the external protector is re-assembled before measuring, the gravity high side must be corrected.
Ø The buffer ring must be assembled with the probe-tube.
Ø In suspending measuring, the descending speed must be lower than 3m/s. When the instrument closing the measuring point, the descending speed should be lower than 1m/s.
FAQ
Q: Are you amanufacturer or trading company?
A: We are aspecialized manufacturer.Q: What are your main products, and used for?
A: Our products include core bit, PDC bit, reaming shell, core barrel, casing, drill rod, SPT equipment, Shelby sampler, drill rig and other drilling parts.
They are used for mineral exploration, geological drilling, geotechnical engineering and soil sampling.Q: How about the delivery terms?
1. Payment: T/T, L/C, Western Union, Paypal, 30% deposit in advance and rest before delivery.
2. Min. order quantity: 1piece.
3. Transportation: By DHL/TNT/Fedex express, air, sea, train.Q: How about discount?
A: Price is based on products and order quantity.Q: Do you accept sample order?
A: Yes sure, please contact us for details.Q: How about your after-sales service?
A: As amanufacturer, we offer promt technology support for all problems and questions. Besides, we accept goods return or replace for quality problem.Q: How does your company control the quality?
A: Quality first. In order to guarantee high quality for our products, Roschen always makes aserious inspection for all products and raw materials in strict procedure. We have obtained certificate of ISO9001:2000 in 2004.For more information please contact:ROSCHEN INC.
ROSCHEN GROUP LIMITED
ROSCHEN HOLDINGS LIMITEDWebsite: http:https://www.roschen.net; http:https://www.roschen.cn
http:https://www.roschen.com