New Smart Home Switch Touch Panel Wall Light Fan Switch AC85-265V Black/White Panel 1gang/2gang/3gan

2018 3Gang 2Way Touch Switch Crystal Glass Panel Black/White Touching Switch AC110-265V UK Standard
Our switch can work under 85-265V, suitable for US, UK and EU etc market. But common EU round back can not offer enough space for our unique flower design, so you will needa mounting box like the right photo.
If you do not have square mounting box, you can:
1.make some DIY to your wall, enlarge the hole for the switch;
2.click the following mounting boxphoto to place order.
SpecificationSize: 86mm*86mm*36mmVoltage: AC110-260V / 50Hz-60HzMax Load: 1.5Kw(if the lamp light up once and then go off, please connect a safety capacitor by Parallel Connection with the lamp)Energy consumption: <0.02mA (Touching switch)Operation environment:-30-+70 degree, less than 98% RHLife Span: 1000,000 times operationDescriptionThis new high-end touch panel ON/OFF switch adopts glass panel design, it is beautiful and fashionable in appearance.Wall mounted installation.High precision capacitance touch control chip, increases the touch sensitivity, reduces trigger
which caused by mistake.Used for controlling a variety of lamp which source of light is LED or traditional lights with AC voltage input. For
instance, all kinds of led lights with 110V-260V input, energy-saving lamps etcIfthe lamp light up once and then go off, please connect a safety capacitor by Parallel Connection with the lamp. This is caused by the
small power of the lamp (for example, led lights or energy-saving lamp)importantNotesThe electric power should be off during installation.Wiring strictly must be done according to the wiring diagramsEach load capacity is Minimum 15W and Maximum 1500W.If the light is less than 15W, a safety capacitor's connection is needed to connect between L and N lines of light. The starting power could not be exceeded 1500W.The size of the installation screw hole is 60mm, and the dimension of mounting box is 75mm*75mm*32mm at least.If the touch testing is operated without the glass panel, please shut down the power first, then fix the switch and install the glass panel, connect the power at last. If power on before put glass panel, the initial capacity of the touch keys will be changed to cause the switch can't work correctly.The following test use 3W led lamp, so a safety capacitor (the yellow one before the lamp) is connected by Parallel with the led lamp
Special Remarks
1. The switch is not suitable for inductive ballast fluorescent.
2. If the switch can't work well, please shut down the power for 1 minutes, then turn on it again.
3. Touch the switch, When lamp is on, the back lights is bright. When it is off, the back lights is slightly bright
4.If one of touch switch hasn't connected any lamps, it is normal that the other switch which connected lamps will flash shortly.
5. If the one way switch hasn't connected any lamps, it is normal that the switch will flash shortly.Attention:
only L1 could be loaded light if the switch is 1gang
only L1 and L3 could be loaded light if the switch is 2gangs
L1, L2 and L3 could be loaded light if the switch is 3gangsProduct Photos from our Clients All over the world
Connection Method
Two Way Switch Matching Instruction:The two way switch only works after matching each other.
Matching Steps:
First, Touching the switch slightly for 5 seconds, take away your hands when you hear the sound of "Di" or backlight flashing.
Second, Touch the other switch, when the switch backlight flashes, it means the success of matching.
Steps to cancel matching:
Press any button of the switch for 10 seconds until hearing two sounds of "Di" or the background light flash twice.(Please don't take away your hand when you hear one" Di" or flash one time). At that time, all the matching has been canceled.Our Service:-Trial orders are welcomed.
-OEM service can be offered.
-Various options of transportation.
-Your inquiry related to our products or price will be replied within 24 hours.
FAQ:1. Q: How can I order? A: Please contact us for the products you like, then we will send you the quotation.2. Q: What is your MOQ?A: 10PCS3. Q: Can I get discount?A: Yes, price depends on quantity, please consult us for details. 4. Q: Can you add our own logo on the products? A: Yes, but need enough quantity to develop, at least 100pcs each kind of panel, and 500pcs total.5. Q: How long a sample order takes?How about bulk order? A: Sample order: normally with in one week. Bulk order: we need to see your order first, and then check with production department.6. Q: What about your package?A: Individual package, and suitable quantity in one carton.