Screw Hair Removal Machine of Slaughtering Equipment

Screw Hair removal machine of slaughtering equipment
The machine is a new type of ploughing machine, which is specially used in pig line, and has been improved synthetically on the basis of the original plough machine. In and out of the pig body and the transport in the body are fully automatic. In order to meet the demand of high production, two knitting machines, one rotating clockwise and the other counterclockwise, are usually used. The position relation is in series. In order to enhance the effect of shaving and wash the pig hair in time, the pig body was washed with hot water of 60 ~ 65 ºC in the process of shaving. The water flow through the filter to the cistern, and the water was controlled by centrifugal pump to recycle again.
Main use and characteristics
1) the equipment is used for shaving the pig body after ironing.
2)a.The whole machine adopts mechanical transmission, no pollution to pig body.
b. Stable operation, long service life.
c. Continuous production, high efficiency.
d. Simple operation, less easily damaged parts.Installation and commissioning
1) Arrange the planing machine according to the process diagram and the specific conditions of the workshop, and determine the installation height and the auxiliary equipment before and after the installation, and make the correction and positioning after the ground foot bolt is buried;
2) connect the water spray pipe outside;
3) check whether the fastening bolts of each bearing seat and the middle of the bearing block are loose;
4) Before commissioning, the lubricating oil shall be filled in each rotating part. The correct turn is to rotate in the counter-clockwise direction in the face of the motor.the point of operation safety
1) it is strictly prohibited to put hands and other things into the screwdriver while working in order to prevent injury or damage to the machine;
2) if the screw shaver has abnormal working sound, it should stop and check immediately to prevent the machine from being damaged and the personnel be hurt;
3) the machine must be cleaned and maintained while stopping, and the power supply is cut off and a warning plate is put up;
4) shut off the power supply after work,
5) the operator should have the knowledge of mechanical and electrical operation,
6) the operator should be familiar with the structure, performance, safety regulations and this specification of the screw shaver, etc.
7) the operator should be trained on the job and be on duty with a license;
8) check daily before each shift;
9) users must establish the necessary rules and regulations as well as the safety operation rules.working principle:
The machine is composed of motor, reducer and drive sprocket to drive the running of the conveying chain. The tensioning mechanism makes the chain always in the state of tensioning, which ensures the smooth operation and adjusts the running speed according to the need. Pig carcass was entered into conveyer by hoist, and the carcass was sealed by manual tools and ground equipment, red, white viscera, quarantine, split half, weighing and other separate processing.Inspection, maintenance, maintenance and troubleshooting methods:
1) the chain can be lubricated once every 2-3 days; if necessary, it can be replaced once a day to ensure smooth transportation. Replace the worn chain regularly.
2) lubricating oil can be replaced once in 2-3 days, if necessary, once a day. Replace bearings that wear too much on a regular basis.
3) after every shaving, the equipment should be cleaned with high pressure water to keep the inside and outside of the body clean; every cleaning should be cleaned to ensure the clean and hygienic equipment and smooth operation.
4) tighten fasteners of fixed planer regularly to reduce loosening. Soft planer is easily damaged, the broken soft planer should be replaced in time. The soft paw of stainless steel can bend again when the deformation is too large and the effect of shaving is affected. The long-term hard planer should be adjusted or replaced if the top wear is too large or the angle and height of the planer do not meet the requirements of shaving.
5) after using for a period of time, the copper bush, copper sleeve and the damaged bearing should be replaced in time to avoid affecting the normal operation of the machinery;
6) since the machine is working in a vibratory state, the connection bolt should be checked for loosening during the use of the machine.
7. Do not exceed the maximum power and load of the equipment every time, so as to avoid damage to the equipment.
8) airlift for a period of time before each use to ensure that the equipment is not abnormal before it is put into use.
9) after the installation and use of the machine, in addition to the usual maintenance, every year after the peak season production to carry out a major overhaul, serious wear parts should be replaced in time to ensure the normal operation of the machine;