China Motion Automatic Sliding Door Sensors

Safety Instruction
Related part should be operated under low voltage condition. All installation process and maintainance should be carried out by the supplier.
Name of Related Parts
▪JST connection ( Red: 24V power cable, Yellow: Relay )
▪COM / NO
▪The indicator will shin for few seconds when object is detected by sensor, indicator lights up.
▪Sensitivity potentiometer
▪Fluctuation up and down, rotation left and right.
Installation
1.Please do the installation in the proper position. Installation height within 3.5m. Please arrange hole (Φ 3.2mm) on the installation module. And hole (Φ12m) for inselting guide line.
2.Please connect the signal cable with the terminal of automatic door.
Brown and Yellow cable: AC/DC12V-24V
Green and White cable: Signal output COM/NO
3.Take the outer cover off, and fix the screws.
4.Finish the cable connection and get on power.
5.Please set the detection range and disjunctor accordingly.
6.Cover with the lid.
Picture of Motion Sliding Door Sensors

Adjustment ( Get on powet )
1.Detection range
Note: Please stand out of the delection range around 5s to ensure the sensor has enough time to finish the self-adjustment.
2.Delection Range
MIN: 0.5*0.4M
MAX: 4*2M
Select different delection range by adjusting sensitivity knob
3.Adjustment of delection direction
( Adjust Direction of front and back/Left and Right flexibly )
Adjusting angle of Plain aeral to get different delection distance and range 30=15x2range
NOTE:
Initial setting is 45 degreed by factory.
All the parameters above are only for reference, detection height is 2.2M.
Detection range will be different because of the making material of door and ground, please adjust the sensitivity by the knob meontioned above.
When it is adjusted to 60 degree, the detection range is the widest, door will keep on closed and open all the time.
Special Note
▪Position should be fixed tightedly to avoid vibrating.
▪Do not place into board or other material.
▪Moving object should be avoided.
▪Fluorescent should be avoided.
▪Do not touch directly, ESD Protection is necessary.
Failure Cause

SymptomCauseMethodDoor&Indicator lose failureDid not get on powerCheck cable connection&power supplyDoor keep on closed and openSensor detected the movement of autodoor, virbration of movement.1.Adjust angle
2.Check the position
3.Adjust sensitivityDoor do not close Red indicator lose failure1.Switch of autodoor controller lose failure
2.Incorrect position
3.Incorrect output of sensorCheck the switch of autodoor controller&setting of output.Door keeps on moving when it rains.Sensor detected the actions of rain.Adopt waterproof accessories.

Parameter
Technology: Microwave&microwave disposer
Transmitting power: <20dBm EIRP
Installation height: 4M(MAX)
Detection Mode: Moving
Power: <2W(VA)
Maximum voltage: 42V AC-60V DC
Maximum switching power: 30W(DC)/60VA(AC)
Guide line: 2.5M
Protection class: IP54
Color: Black/silvery
Anti-interence performance: R&TTE 1995/5/EC, EMC 89/366/EEC
Power voltage: 12V to 30 V AC+/-10%( 50Hz to 60Hz ): 12V to 36V DC
Size: 120mm(W)x80mm(H)x50mm(D)
Frequency: 24, 125GHz
Launch frequency density:<5mW/cm²
Installation angle: 0-90 degree(lengthways)-30 to+30(lateral)
Min detection speed: 5cm/s
Detection ranhe: 8m*4m(installation Height 2.2M0
Maximum current: 1A
Retention time: 0.5s
Working temperature: -20ºC to +55ºC
Sheating material: ABS plastic
Accessory List & Optional Parts
The Picture of Automatic Doors
Other Automatic Doors Accessories
1. Operation
The automatic door operator is to be fully electronic operator, housed in a fully anodised aluminum transom section.
2.Controller
The intelliget controller unit can be programmed for connection to any security/alarm systems, is self monitoring and calibrating, has memory for all data on door stoke and brake positions.
3.UPS
The operator has built-in uninterrupted power supply (Battery back up) operation and security during power failure.
4.Belt Drive
Drive is by way of toothed belt, which is reinforced with fiberglass tensile members, and has nylon facing surface for tooth protection on the pulleys. This combination produces silent accurate operation.
5.Tracking
The track is self-cleaning duel linear. The upper track is made of harder stronger alloy 6351T6, and can be replaced without moving the transom. The wheel trolley is fitted with anti-rise wheels, resulting in very firmly fitted doors with operation free of any racking.
6.Locking
Electromechanical Locking: An electric lock option is available to give total security and can be adapted where manual locking cannot be achieved, i. E. frameless toughened Glass doors. Lock is the microprocessor controlled electric locking system. The microprocessor monitors all aspects of the lock functions. E. G. To ensure the door is fully closed when the lock is 100% engaged. Terminal outputs are available to signal to security system both door positions and lock status.