Electrochemical Multichannel Potentiostat

CS series multichannel potentiostat CS310X(X is the number of channels) can achieve simultaneous measurements for up to 8 channels. The specifications of each channel are identical: current control range is ±200mA(up to ±500mA for 4-channel potentiostat), potential control range is ±10V. It supports floating mode, and uses Ethernet connection.
Each channel is completely independent. The user can choose to use just one or some of the channels. multichannel potentiostat brings convenience to those who have many samples, and is an ideal device for studies of energy materials, metal corrosion etc.
ModelCS3104CS3105CS3106CS3107CS3108Number of channels45678
Applications:(1) Reaction mechanism of Electrosynthesis, electrodeposition (electroplating), anodic oxidation, etc.(2) Electrochemical analysis and sensor;
(3) New energy materials, advanced functional materials, photoelectronic materials;
(4)Corrosion study of metals in water, concrete and soil etc;
(5) Fast evaluation of corrosion inhibitor, water stabilizer, coating and cathodic protection efficiency.SpecificationsSpecificationsNumber of channels: 4~8 channelsChannel insulation resistance:>100MΩCommunication: network interfacePotential control range: ±10VConstant current control range:±200mA
(up to ±500mA for 4-channel potentiostat)Potential accuracy: 0.1%xfull range±1mVCurrent accuracy:0.1%xfull rangePotential resolution:10mV(>100Hz), 3mV(<10Hz)Current resolution:<1pAPotential rise time:<1ms(<10mA),<10ms(<2A)Current range: 2nA ~200mA, nine rangesReference electrode input impedance:1012Ω||20pFMaximum current output: 200mA
(up to 500mA for 4-channel potentiostat)Compliance: ±12VCurrent increment during scan: 1mA @1A/msCV and LSV scan rate: 0.001mV~10000V/sPotential increment during scan: 0.076mV @1V/msCA and CC pulse width: 0.0001~65000sDPV and NPV pulse width: 0.0001~1000sSWV frequency:0.001~100KHzCV minimum potential increment: 0.075mVAD data acquisition:16bit@1MHz,20bit @1kHzIMP frequency:10mHz~1MHzDA resolution:16bit, setup time:1msCurrent and potential range: automaticLower-pass filter: covering 8-decadeElectrochemicalImpedance Spectroscopy(EIS) (**Option)DCoffsetcompensationFrequency range:10mHz~1MHzAC signal amplitude: 1mV~2500mVFrequency accuracy:0.005%Signal resolution: 0.1mV RMSDDS output impedance: 50ΩDC Bias: -10V~+10VWave distortion: <1%Waveform: sine wave, triangular wave, square waveScan mode: Logarithmic/linear, increase/decreaseDCoffsetcompensationMaximum integral time:106 cycles or 105sMeasurement delay:0~105SMinimum integral time:10ms or the longest time of a cycleDCoffsetcompensationPotential compensation range: -10V~+10VCurrent compensation range: -1A~+1ABandwidth adjustment: automatic and manual, 8-decade frequency range
Software
Techniques in each channel:
Open Circuit Potential(OCP), Potentiostatic(I-T Curve), Galvanostatic, Potentiodynamic (Tafel plot), Galvanodynamic
Multi-Potential Steps, Multi-Current Steps, Potential Stair-Step (VSTEP), Galvanic Stair-Step (ISTEP)
: Chronopotentiometry(CP),Chronoamperometry(CA),Chronocoulometry (CC)
Cyclic Voltammetry(CV), Linear Sweep Voltammetry(LSV)
Battery charge and discharge, Galvanostatic charge and discharge (GCD)**Note: We have options of the following two modules to add in the above basic functions.
You can add below module(s) for all channels, or add to some of the channels.
1. EIS module
EIS vs Frequency (IMP), EIS vs Time (IMPT), EIS vs Potential (IMPE)
2.Voltammetry module
Cyclic Voltammetry (CV), Linear Sweep Voltammetry (LSV), Staircase Voltammetry (SCV), Differential Pulse Voltammetry (DPV), Normal Pulse Voltammetry (NPV), Square wave voltammetry (SWV), ACvoltammetry (ACV), Differential Normal Pulse Voltammetry (DNPV), 2nd Harmonic A. C. Voltammetry (SHACV), Fourier Transform AC Voltammetry(FTACV), Potentiostatic stripping, Linear stripping, Staircase stripping, Square wave stripping, Simultaneous Measurements
In each channel, the user can choose a same method. The parameters setting in each channel is the same. In the below picture for instance, choose four of the 8 channels to do EIS test, set the parameters in each channel once, then start EIS tests simultaneously.In each channel, the user can also choose different experiments. Set the parameters for experiment in each channel and start simultaneous measurements. As is shown in the below picture, EIS, galvanostatic charge and discharge, CV, and polarization curve tests are conducted at the same time.