China C43-31 Colorful Alkyd Topside Paint

C43-31 COLORFUL ALKYD TOPSIDE PAINTQ/GHTD 34
COMPOSITION
The paint consist of alkyd resin, titanium white and tinting pigments, drier, solvent and etc..
PRINCIPAL CHARACTERISTICS
·good color retention and weather ability.
·glossy film with gay color.
·good flexibility and adhesion, resistance to dash of seawater.
·a certain degree of resistance to water and oil.
·good applicability.
·Approved by CCS.
USAGEIt is applied to be as a finish coated over hull areas and superstructure
above water line of ship, and steel structure on land.
COLOUR AND APPEARANCE

Product codeProduct typeColour & appearance07-22C43-31(861-2)Light grey gloss07-24C43-31(863)Light grey gloss07-25C43-31(864)Cream yellow gloss07-26C43-31(865-1)Middle grey gloss07-29C43-31(867)White gloss07-32C43-31(869-1)Blue grey gloss07-35C43-31(870-1)Light grey gloss07-36C43-31(882-1)Black gloss

APPLICATION DATA

Product
codeProduct
typed.f.t.
μmw.f.t.
μmTheoretical Coverage Rate g/m207-22861-235788797-2486335738207-2586435788707-27865-135738607-2986735768507-32869-135789707-35870-135789407-36882-1357980

Flash point≥35ºC
Dry time
·Touch dry ≤4h
·Hard dry≤24h
interval before recoating

substrate temperature5ºC20ºC30ºCMin.36h24h16hmax.3 months

RECOMMENDED two coats with 70μm of d.f.t. or more
NUMBER OF COATS
PREVIOUS f53-31(712) Red lead phenolic anti-corrosive paint
COATINGc53-31(716) Red lead alkyd anti-corrosive paint
SYSTEM725 Zinc yellow phenelic anti-corrosive paint
706 Anti-corrosive Paint
842 epoxy IMO Anticorrosive Paint
C53-38 Aluminum Dust and Red Iron Alkyd Anti-corrosive Paint
Pretreatment
Recommended Substrate conditionsPrevious coat of paint shall be thoroughly dry..Remove oil, grease, dirt and foreign matter on the previous film completely.APPLICATION CONDITIONSMust be at least 3ºC above dew point to avoid condensation.The relative humidity is below 85%.Application method
Airless spray Recommended thinner: thinner 104
Thinning ratio: 0-5% (m/m)
Nozzle orifice: 0.4-0.5 mm
Nozzle pressure: 12-15Mpa (approx, 120-150kg/cm2)
Air sprayRecommended thinner: thinner 104
Thinner ratio: 0-10% (m/m)
Nozzle orifice:2-3 mm
Nozzle pressure: 0.3-0.4MPa(approx, 3-4kg/cm2)
Roller/brush (limited to small area maintenance )
Recommended thinner: thinner 104
Thinner ratio: 0-3% (m/m)
CLEANER Thinner 104SAFETY PRECAUTIONReference to Material Safety Data Sheet(MSDS).
SHELFLIFE 12 months
NOTE Please read "Application guide" carefully beforehand, in order to use the product manufactured by our factory properly.DECLARATIONThe information given in the sheet, which is based upon the background of experience in our testing and practice, may be as a guide of application. Since condition of application and service may be beyond our control, no liability can be accepted on basis of these data, and responsibility is taken for the quality of product itself by our factory beyond all doubt.The factory reserves the right to modify data in accordance with the quality of product being improved increasingly without notice.