China Hydrolysis Type Self-Polishing Antifouling Paint

Description
This is a one-component acrylic hydrolyzed antifouling coating based on ion exchange technology which has good antifouling properties. This antifouling effect is achieved by self-polishing properties and micro-erosion properties while reducing hull degradation. Use as a top coat only in an immersion environment. Suitable for construction on carbon steel substrates coated with certified primers and intermediate paints. It can be applied when the surface temperature is below 0 °C.
Usage
Recommended for underwater hulls of newbuilding and docking. Designed for ships with medium to low speeds and high sailing rates. As part of a complete coating package, this product provides up to 36 months of anti-fouling function.
Certification
Comply with AFS/CONF/26 in the IMO Anti-Fouling System Convention, free of organotin, free of DDT and other toxic chemicals
Data
Performance Test / Standard Description
Volume solids content ISO 3233 55±2%
Flash point ISO 3679 Method 125°C
Density theoretical value 1.78Kg/L
VOC-ChinaGB/T23985-2009 (ISO11890-1) 393g/L
The data listed is based on laboratory tests and actual mass production may vary slightly.
Film thickness
Dry film thickness 200μm - 280μm
Wet film thickness 363μm - 509μm
Theoretical coating rate 0.648Kg/m 2 - 0.901Kg/m 2
In actual construction, the paint loss factor due to coating equipment, environment and spray techniques is generally calculated as 1.2-1.5.
The effective period of antifouling paint is directly related to the dry film thickness of antifouling paint. Customers should advance the ship type, sailing sea area, docking interval and other information in advance.
Surface treatment
To ensure long-lasting adhesion of the next coating, all surfaces must be clean, dry and free of contaminants.

ECO-FRI 891 Hydrolyzed self-polishing antifouling paint
Description
This is a one-component acrylic hydrolyzed antifouling coating based on ion exchange technology which has good antifouling properties. This paint effect is achieved by self-polishing properties and micro-erosion properties while reducing hull degradation. Use as a top coat only in an immersion environment. Suitable for construction on carbon steel substrates coated with certified primers and intermediate paints. It also can be applied when the surface temperature is below 0 °C.
Usage
Recommended for underwater hulls during newbuilding and docking. Designed for ships with medium to low speeds and high sailing rates. The product offers 12 to 24 months of anti-fouling protection at an excellent price/performance.
Certification
Comply with AFS/CONF/26 in the IMO Anti-Fouling System Convention, free of organotin, free of DDT and other toxic chemicals
Color
Crimson, light red
Product data
PerformanceTest / Standard Description
Volume solids content ISO 3233 53±2%
Flash point ISO 3679 Method 125°C
Density theoretical value 1.77Kg/L
VOC-China GB/T23985-2009 (ISO11890-1) 409g/L
The data listed is based on laboratory tests and actual plant mass production may vary slightly.
Film thickness
Typical recommended specification range
Dry film thickness: 100μm - 200μm
Wet film thickness: 188μm - 377μm
Theoretical coating rate: 0.335Kg/M2 - 0.669Kg/M2
Surface treatment
To ensure long-lasting adhesion of the next coating, all surfaces must be clean, dry and free of contaminants.Substratesurface treatment
Minimum
Maximum
Painted SurfaceNew lacquer or antifouling: Remove any dirt that affects the adhesion of the intermediate lacquer.
Exceeding the longest coating interval may require cleaning, sanding or applying other coatings, as appropriate.
Aging antifouling coating with saponified layer: thoroughly rinsed with fresh water at a minimum nozzle pressure of 20 MPa.New lacquer or antifouling: Remove any dirt that affects the adhesion of the intermediate lacquer. Exceeding the longest coating interval may require cleaning, sanding or applying other coatings, as appropriate.
Aging antifouling coating with saponified layer: thoroughly rinsed with fresh water at a minimum nozzle pressure of 34 MPa.
Construction method
Spray: Airless spray.
Brush: Can be used. Be careful to achieve a specific dry film thickness.
Roller: Can be used. Be careful to achieve a specific dry film thickness.
Product mixing
Single component
Thinner / cleaning agent
Thinner: JINDUN 102 Thinner
Airless spray guide parameters
Nozzle aperture (inch/1000): 21-31
Nozzle pressure (min): 15MPa/2100 psi
Drying and curing time
Substrate temperature -10°C 0°C 10 °C 23 °C 40 °C
10 hours 2.5 hours 75 minutes 1 hour 30 minutes
Overcoat after drying, minimum interval
27 hours 16 hours 9 hours 8 hours 7 hours
Dry/cured to submersible
72 hours 48 hours 24 hours 24 hours 16 hours
The max Interval before recoating, please consult the JINDUN technician.
When quickly applying a third or more antifouling coating, it is recommended to double the time before immersion.
The drying and curing times were determined based on temperature and relative humidity, relative humidity below 85%, and dry film thickness in the average dry film thickness.
Table (touch) dry: lightly pressed with a finger without fingerprint residue or no adhesion.
Overcoat after drying, minimum interval: The recommended minimum time interval for the application of the next coat.
Dry/curing to submergible: The shortest time before the coating can be permanently immersed in seawater.
When using a two-component epoxy anti-corrosive primer, the recommended connecting paint for the anti-fouling paint is: JDGuard5345 modified epoxy intermediate paint or V218 vinyl joint paint, both of which have been carried out for many years. Coating verification, with high reliability.
When using 615 aluminum powder chlorinated rubber antirust paint and 616 iron red chlorinated rubber antirust paint as antirust paint, the antifouling paint can be directly applied to the chlorinated rubber antirust primer without connecting paint.
Packaging
Paint 19 (kg) 10 (L)
Storage
Must be stored in accordance with national regulations. The storage environment should be dry, cool, and well ventilated, away from heat and fire. The packaging container must be kept closed. Handle with care.
Shelf life at 23 °C
ECO-FRI 891 Hydrolyzed Self-polishing Antifouling Paint 12 month(s)
For colors other than red, the shelf life is 6 months.
The above is the shortest shelf life and must be tested to determine if the quality is acceptable.
Precautions
This product is for professional use only. Construction workers and workers need training, experience, ability and equipment to properly mix/mix and apply paint according to Golden Shield's technical documentation. Construction personnel and workers need to use appropriate personal protective equipment when using this product. This guidance is based on existing product knowledge. Any changes proposed to suit the situation on the site must be approved by the responsible Golden Shield representative before use.
Health and safety
Please check the safety notice on the container packaging. Use in well ventilated conditions to avoid inhalation of paint mist and avoid skin contact.
If it is accidentally splashed on the skin, rinse immediately with a suitable detergent, soap and water. If you accidentally enter your eyes, apply plenty of water and rinse immediately.
Color difference
When used, products that are primarily used as a primer or antifouling may have a slight color change between batch and batch. Similarly, there may be fading and chalking in climatic conditions exposed to sunlight.
Statement
The information provided in this manual is based solely on our knowledge gained in the laboratory and in practice. Golden Shield's products are considered semi-finished products, so the use of the products is usually outside our control. Therefore, Golden Shield only guarantees the quality of the product itself. In order to comply with local regulations, the product may be properly adjusted, and we reserve the right to modify the instructions without notice. Users should consult Golden Shield for specific guidance on the applicable performance of related products for their own needs and specific applications.

Construction method
Spray: Use airless spray.
Brush: Can be used. Be careful to achieve a specific dry film thickness.
Roller: Can be used. Be careful to achieve a specific dry film thickness.
Product Specifications
ECO-FRI 892 Hydrolyzed
Product mix
Single component
Thinner
Thinner: JIDNUN 102 Thinner
Airless spray guide parameters
Nozzle aperture (inch/1000): 21-31
Nozzle pressure (minimum): 15MPa/2100 psi
Drying and curing time
Substrate temperature -10°C 0°C 10 °C 23 °C 40 °C
Table (touch) dry 10 hours 2.5 hours 75 minutes 1 hour 30 minutes
Overcoat after drying, minimum interval 27 hours 16 hours 9 hours 8 hours 7 hours
Dry/curing to submersible 72 hours 48 hours 24 hours 24 hours 16 hours
For the largest overcoating interval, please consult the JINDUN technician.
When applying two or more antifouling coatings quickly, it is recommended to double the time before immersion.
The drying and curing times were determined based on temperature and relative humidity, relative humidity below 85%, and dry film thickness in the average dry film thickness.
Table (touch) dry: lightly pressed with a finger without fingerprint residue or no adhesion.
Overcoat after drying, minimum interval: The recommended minimum time interval for the application of the next coat.
Dry/curing to submergible: The shortest time before the coating can be permanently immersed in seawater.
Packaging
Paint 19 (kg) 10 (L)
Storage
Must be stored in accordance with national regulations. The storage environment should be dry, cool, and well ventilated, away from heat and fire. The packaging container must be kept closed. Handle with care.
Shelf life at 23 °C
ECO-FRI 892 Hydrolyzed Self-polishing Antifouling Paint 12 month(s)
For colors other than red, the shelf life is 6 months.
The above is the shortest shelf life and must be tested to determine if the quality is acceptable.
Precautions
This product is for professional use only. Construction workers and workers need training, experience, ability and equipment to properly mix/mix and apply paint according to Golden Shield's technical documentation. Construction personnel and workers need to use appropriate personal protective equipment when using this product. This guidance is based on existing product knowledge. Any changes proposed to suit the situation on the site must be approved by the responsible Golden Shield representative before use.
Health and safety
Please check the safety notice on the container packaging. Use in well ventilated conditions to avoid inhalation of paint mist and avoid skin contact.
If it is accidentally splashed on the skin, rinse immediately with a suitable detergent, soap and water. If you accidentally enter your eyes, apply plenty of water and rinse immediately.
Color difference
When used, products that are primarily used as a primer or antifouling may have a slight color change between batch and batch. Similarly, there may be fading and chalking in climatic conditions exposed to sunlight.
Statement
The information provided in this manual is based solely on our knowledge gained in the laboratory and in practice. Golden Shield's products are considered semi-finished products, so the use of the products is usually outside our control. Therefore, Golden Shield only guarantees the quality of the product itself. In order to comply with local regulations, the product may be properly adjusted, and we reserve the right to modify the instructions without notice. Users should consult Golden Shield for specific guidance on the applicable performance of related products for their own needs and specific applications.